Zehntner ZOL 1150 Скачать руководство пользователя страница 24

Страница: 24 / 36

Page 24

Error lamp

Indicates an error. This indicator has always the same
status as the red status LED (7) on the measuring head.

Gloss value
alarm

Indicates that the gloss value is out of range. This
indicator has the same status as the output "GLOSS
VALUE ALARM" on the connector J2 Pin 5 of the
measuring head. The gloss range can be set in the
Settings page of the web interface tool.

Gloss value

Displays the actual gloss value. This value is updated
once a second.

Maximal value

Displays the maximal value of the 100 single
measurements that were used to calculate the gloss
value.

Minimal value

Displays the minimum value of the 100 single
measurements that were used to calculate the gloss
value.

Standard
deviation

Displays the standard deviation of the 100 single
measurements that were used to calculate the gloss
value.

Time

Indicates the time of the measurement.

W10 Gloss value

graph

The graph shows the gloss value (y axis) over time

(x axis).

W11 Graph settings

These adjustment tools can be used to modify the
display mode of the graph.

W12 Geometry

selection

Selection of the active geometry.

Содержание ZOL 1150





































Результаты поиска

Содержание ZOL 1150

Отзывы:

Похожие инструкции для ZOL 1150

Бренды по названию

Популярные бренды

Zehntner ZOL 1150, Инструкция по эксплуатации

Результаты поиска

Содержание ZOL 1150

Отзывы:

Похожие инструкции для ZOL 1150

Бренды по названию

Популярные бренды