ZD T7AH-2400 Скачать руководство пользователя страница 27

Страница: 27 / 34

◇

To Enter the Function Mode

●

Turn the transmitter on.

●

From the main screen press the DOWN and SELECT keys simultaneously.

●

The system is now in Function Mode and will display the last screen that was

used in Function Mode.

◇

To Exit the Function Mode

●

Press the DOWN and SELECT keys simultaneously. The system will return to

the main screen.

◆

List Modes

The list mode screens display all the functions on screen, allowing the access of

any function without having to scroll through each screen. Note that there are two

list modes: a System Setup list mode that displays all the system setup functions

and a Function list mode that displays all the system programming functions.

To enter the System Setup List Mode, with the system on and in any System Setup

function, press the UP and SELECT keys simultaneously.

To enter the Function List mode, with the system on and in any function mode screen,

press the UP and SELECT keys simultaneously.

In either List Mode, pressing the UP and DOWN keys will move the cursor to the

desired function. Then pressing the DOWN and SELECT key simultaneously will

access the selected function.

10.3 Function Mode Functions

◆

Dual Rate and Exponential

The Dual Rate and Exponential function allows two control rates to be programmed

and selected with a switch. Dual rates and exponentials are available on the aileron

, elevator and rudder channels. Changing the dual rate value not only affects the

maximum control authority but also affects the overall sensitivity of control. A higher

rate yields a higher overall sensitivity.

Dual rates can be controlled by their respective dual rate switches (aileron, elevator

and rudder). An auto dual rate function is available that allows to automatic

selection of the desired rates via the three-position flight-mode switch.

Exponential values are adjustable from -100% to +100%. The factory default

settings for both the 0 and 1 switch positions are 100%. Either switch position may

be selected as the low or high rate by placing the switch in the desired position and

adjusting the value accordingly.

[

FUNCTION

LIST

]

EXP

AUTO

SWASH

MIX

REV

SUB

TRIM

TRAV

ADJ

CURV

ST1

THRO

HOLD

CURV

NOR

CURV

ST1

CURV

ST2

CURV

NOR

ASE and DECREASE key

and

DOWN

key

SELECT

key

CLEAR

key

CURV

NOR

INCREASE

and

DECREASE

key

[

FUNCTION

LIST

]

CURV

ST2

PROG

MIX2

REVO

MIX

GYRO

SENS

PROG

MIX1

PROG

MIX3

TIMER

and

DOWN

key

SELECT

key

CLEAR

key

MONITOR

[

EXP

]

POS

AILE

100

EXP

LIN

OUTPUT

Press

adjust

value

Press

enter

DUAL

Press

enter

Function

Mode

RATE

and

EXPONENTIAL

Press

select

desired

function

Press

return

value

default

setting

[

EXP

]

POS

100

EXP

LIN

OUTPUT

INCREASE

and

DECREASE

key

and

DOWN

key

Press

enterFunction

Mode

AILE

Содержание T7AH-2400



































Результаты поиска

Содержание T7AH-2400

Отзывы:

Похожие инструкции для T7AH-2400

Бренды по названию

Популярные бренды

ZD T7AH-2400, Инструкция по эксплуатации

Результаты поиска

Содержание T7AH-2400

Отзывы:

Похожие инструкции для T7AH-2400

Бренды по названию

Популярные бренды