29
30
◆
Travel Adjust
The Travel Adjust function allows the precise end-point adjustments of all seven
channels in each direction independently. The travel adjust range is from 0–150%.
Channel available for programming are:
●
THRO: Throttle
●
AILE: Aileron
●
ELEV: Elevator
●
RUDD: Rudder
●
GEAR: Retractable Landing Gear
●
FLAP: Flap
●
AUX2: Auxiliary 2
◇
To Access the Travel Adjust Function
Press the DOWN and SELECT keys simultaneously to access the Function Mode.
In Function Mode, use the UP or DOWN key to select the TRAVEL ADJUST screen.
Press the SELECT key to access the desired channel.
Move the selected channel’s stick or switch in the desired direction that you wish to
adjust.
Press the INCREASE or DECREASE keys to adjust the end-point position for that
selected channel's direction.
◇
To Access the Elevator-to-Flap Mixing
In the Function Mode, use the UP or DOWN key to select the ELEVATOR TO FLAP
MIXING function and press the UP and DowN keys simultaneously to access.
Note: The flap mix switch, or the Mix switch, no matter which is selected, must be
in the“ON” position to adjust values.
To adjust the rate value, with the switch on, move the elevator stick in the desired
position and press the INCREASE or DECREASE key to adjust the desired mix value.
◇
To Select the Switch to Operate the Flap Mix
Press the SELECT key to highlight SW.
Press the INCREASE or DECREASE key to select the MIX or FLAP0 switch.
[
TRAVEL
ADJUST
]
THRO
H
100
%
L
100
%
ELEV
D
100
%
U
100
%
AILE
L 100
%
R
100
%
RUDD
L
100
%
Selected
channel
Press
to
enter
TRAVEL
ADJUST
Press
to
enter
Function
Mode
Press
to
return
value
to
default
Press
to
select
desired
channel
R
100
%
Press to adjust value
Press
to
enter TRAVEL
ADJUST
[
ELEV
-
FLAP
MIX
]
Press
to
enterFunction
Mode
Press
to
select desired
channel
Press to adjust value
RATE
:
D
0 %
SW
:
FLAPO
U
0%
ON
[
AILE
-
RUDD
MIX
]
Press
to
enter TRAVEL
ADJUST
Press
to
enter Function
Mode
Press
to
select desired
channel
Press to adjust value
RATE
:
0
%
SW
:
MIX
OFF
◆
Elevator-to-Flap Mix Function
When the Elevator-to-Flap Mixing System is active, and a value of flaps is inputted,
the flaps will be deflected each time the elevator stick is used. The actual flap
movement is independently adjustable for both up and down elevator. When used
in this manner, the aircraft pitches much more quickly than normal. The uppermost
position of the Flap Mixing Switch or the Mix Switch can be used to activate the
Elevator-to-Flap Mixing function. When you want to reverse the mixing directions,
press the - key to change the mixing value from + to - (or - to +).
◆
Aileron-to-Rudder Mixing
If the Aileron-to-Rudder Mixing function is designed, the rudder servo will move
when the aileron stick is used, eliminating the need to coordinate these controls
manually. This mixing program can be turned ON/OFF by a switch. The switches
that can be selected are shown below, with their abbreviations as they appear on
the screen and the corresponding switch positions. Mix values are adjustable
from 0 to 125%. When adjusting the mix value, if an opposite mixing direction of the
rudder servo is required, simply press the INCREASE or DECREASE key to change
the mixing value from + to - or - to +. This will reverse the mixing direction of the
rudder from its original direction.
●
ON: Mixing Always ON
●
MIX Switch ON/OFF Using Mixing Switch
●
Flap 0 Switch ON/OFF Using Flap Mix Position 0
●
Flap 2 Switch ON/OFF Using Flap Mix Position 2
