31
32
◇
To Access the Aileron-to-Rudder Mix Function
Press the DOWN and SELECT keys simultaneously to access the Function Mode.
In Function Mode, use the UP or DOWN key to select the AILE-RUDD MIX screen.
Press the SELECT key to select RATE or SW (switch).
◇
To Adjust the Mix Value
With RATE highlighted, press the INCREASE or DECREASE keys to adjust the
mix value. Note: reversing mix directions is accessible.
◇
To Assign a Switch
With SW be choosed, press the INCREASE or DECREASE keys to select the
desired switch used to turn on/off the mix (Flap 0 or Mix).
◆
Flap System
The purpose of the Flap System is to set the flap and elevator positions for landing
and takeoff. This is accomplished by selecting values for the elevator and flaps to
be activated when the Land Switch is engaged. Three flap and elevator positions
are available. The landing system can also be activated by a preset position of the
throttle stick. Refer to the Automatic Landing Attitude section for more information
on how to select the preset throttle position.
Note: The Flap System is only be accessed when SYSTEM is selected under Flap
in the Input Select screen. See page 46 for more detail
◇
Accessing and Utilizing the Flap System
Press the UP and SELECT keys simultaneously to enter the Function Mode.
Press the UP or DOWN keys until FLAP SYS appears in the upper left portion of the
LCD. Press the SELECT key to move the cursor at the desired function (i.e., ELEV,
FLAP , SPOI, AUTO). Note: The flap system can only be accessed when SYSTEM
is selected in the Input Select screen under flaps. See page 41 for more details.
Press the UP or DOWN keys to set the flap and elevator travel. The UP key adds up
flap/elevator and the DOWN key adds down flap/elevator. The input is adjustable
from 125% for flap and -200% for elevator.
◆
Automatic Landing
When the Automatic Landing Function is active, the throttle stick will activate the
landing system you have just set up. Any point of throttle stick travel can be set as
the “auto-land” point. Once the throttle stick passes through this point and the
LAND switch is in the MID, or land position, the landing system will be activated.
Thus, the elevator and flaps would be activated. If the flap mixing switch is not in
the LAND position, the throttle stick operation would have no effect on the landing
system.
◇
To Activate the Automatic Landing Feature
In the FLAP SYS. screen, press the SELECT key until AUTO is selected.
Press the INCREASE or DECREASE key to activate the AUTOMATIC LANDING
SYSTEM. Press the INCREASE or DECREASE key to adjust the value (0% = low
stick while 100% = full stick). To clear the auto land point, press CLEAR key and
the display will return to INH.
◆
Differential Aileron Mixing
Note: Only available when Flaperon or Elevon is selected, the Differential System
is available (see Tail Wing Type Page 44).
The Differential Aileron function allows precise electronic adjustments of the up vs
. down aileron travel of both ailerons. Aileron differential is used to reduce unwanted
yaw characteristics during roll inputs. In order to access the Differential Function,
flaperon or elevon wing mixing must be selected and two servos must be used to
operate the ailerons.
[
FLAP
SYS
.]
NORM
FLAP
ELEV
NORM
UP100
%
0
0
0
MID
LAND
AUTO INH
DN100
%
0
%
Press
to
enter
FLAP
SYSTEM
Press
to
enter
Function
Mode
Press
to
return
value
to
default
Press
to
highlight
the
desired
function
Press to adjust value
[
DIFFERENTIAL
]
Press
to
enter
DIFFERENIAL
Press
to
enterFunction
Mode Press
to
return value
to
default
Press to adjust value
FLAPERON
NORM
0
%
[
FLAP
SYS
.]
NORM
FLAP
ELEV
NORM
Up100
%
0
0
MID
LAND
AUTO INH
DN100
%
0
%
Press
to
enter
FLAP
SYSTEM
Press
to
enterFunction
Mode
Press
to
return value
to
default
Press to adjust value
0
