PROGRAMMING FAVOURITE POSITIONS FOR TRANSMITTERS AND INPUTS IN1, IN2
• For radio transmitters and inputs ▼, ▲ (LOCAL 1 or LOCAL 2), the operator can program two favourite positions known as percent of closure of the
shutter. The positions are shared between all transmitters assigned to the specific shutter in local mode and inputs ▼, ▲ working in local mode. The
favourite positions can be called out independently of the shutter position.
• To call out the first favourite position, press and hold longer (>2 s) the transmitter’s button assigned for upward shutter movement (the button assigned
in local mode) or the button connected to input ▲ for the shutter.
• To call out the second favourite position, press and hold for longer (>2 s) the transmitter’s button controlling the shutter’s downward movement (the
button assigned in local mode) or the button connected to input ▼ of the shutter.
CAUTION: Performing several calls of favourite settings with the shutter starting movement from intermediate positions could result in loss of
calibration. Re-calibration is performed automatically after complete opening or closing of the shutter.
DIRECT PROGRAMMING OF FAVOURITE SETTINGS USING PROG BUTTON
• Independently from the radio transmitter, favourite shutter positions are always programmed using buttons 1 and 2.
• To program the favourite positions, place the shutter in one of the extreme positions (top or bottom).
CONFIGURING THE FIRST FAVOURITE POSITION
1. Open or close the shutter completely.
2. Briefly (1 s) press the PROG button on the receiver – the STATUS LED will light up and the ▼, ▲ LEDs assigned to motor M1 will light up.
3. From the moment of activation of LEDs: ▼, ▲ assigned to the M1 motor, within less than 2 s briefly press PROG and select the number of shutter you
want to assign opening and closing time. Shutter selection is signalled by activation of LEDs ▼, ▲ M1 for shutter 1 and M2 for shutter 2, respectively.
4. After selecting the shutter, wait approx. 2 s for the STATUS LED to go off.
5. After the STATUS LED goes off, wait for approx. 15 s. After the third quick blink of the STATUS LED, in less than 5 s briefly press PROG.
6. The shutter will begin moving up or down depending on what position it was at the start of movement. Once the shutter reaches the position you want to
program as the first favourite setting, press the “1” button on the transmitter or the local button connected to input ▲ (by default: shutter up). The shutter
will stop.
7. Correct programming of the time values is signalled with several quick blinks of the STATUS LED and going off of the ▼, ▲ diodes associated with the
specific shutter.
CONFIGURING THE SECOND FAVOURITE POSITION
1. Open or close the shutter completely.
2. Briefly (1 s) press the PROG button on the receiver – the STATUS LED will light up and the ▼, ▲ LEDs assigned to motor M1 will light up.
3. From the moment of activation of ▼, ▲ LEDs assigned to the M1 motor, within less than 2 s briefly press PROG and select the number of shutter you
want to assign opening and closing time. Shutter selection is signalled by activation of the applicable ▼, ▲ LEDs: M1 for shutter 1 and M2 for shutter 2,
respectively.
4. After selecting the shutter, wait approx. 2 s for STATUS LED to go off.
5. After the STATUS LED goes off, wait for approx. 15 s. After the third quick blink of the STATUS LED, in less than 5 s briefly press PROG.
6. The shutter will begin moving up or down depending on the position it was in when the movement started. After reaching the position you want to program
as the second favourite setting, press „2” on the controller or local button connected to input ▼ (by default: shutter down). The shutter will stop.
7. Correct programming of the time values is signalled with several quick blinks of the STATUS LED in green and going off of the LEDs associated with the
specific shutter.
CHANGING FAVOURITE POSITIONS USING EXTA LIFE APPLICATION
You can set favourite positions for radio transmitters and local inputs using EXTA LIFE app, having first paired the SRM-22 with the controller. To do so,
select „Configure” from the receiver’s editing menu. You will be transferred to configuration screen where you can set basic parameters for the specific
shutter controller.
To change the favourite position, click the correct field to open the slider. Using the slider, set the new value for the favourite position and press “Save
changes”. To save your new configuration in the SRM-22 controller, press „Save”.
PROGRAMMING THE TIME OF MOVEMENT FOR SHUTTERS
CAUTION: You must correctly program the opening and closing times when controlling the shutter from the mobile app or when defining the
“favourite” positions. These values are used for calculating percentage values defined as the degree of closure of the shutter.
• A 2-second offset is added to the programmed periods for efficient opening / closing of shutters to account for different operational speeds of motors.
That offset is not included during calculation of percentage values.
• Closing and opening times may be programmed for 1 s to 10 minutes. You can configure time from the receiver (using the PROG button) or remotely
using EXTA LIFE mobile app working with the controller.
1. DIRECT PROGRAMMING OF TIME USING THE PROG BUTTON
To properly program time for opening and closing, set the shutter in the extreme top position, i.e. fully open.
1. Briefly (1 s) press the PROG button on the receiver – the STATUS LED will light up and ▼, ▲ LEDs assigned to motor M1 will light up.
2. From the moment of activation of LEDs: ▼, ▲ assigned to the M1 motor, within less than 2 s briefly press PROG and select the number of shutter you
want to assign opening and closing time. Shutter selection is signalled by activation of LEDs ▼, ▲ M1 for shutter 1 and M2 for shutter 2, respectively.
3. After selecting the shutter, wait approx. 2 s for the STATUS LED to go off.
4. After the STATUS LED goes off, wait for approx. 10 s. After the second quick blink of the STATUS LED, briefly press PROG.
5. The shutter will start closing and the STATUS LED will start blinking at the same time every 1 s which signals the measuring of “closing time”. When the
shutter reaches the extreme bottom position, press the PROG button again. The shutter will start opening and the opening time will be programmed.
When the shutter reaches the extreme upper position, press PROG again. This is the end of programming procedure for opening / closing time. These
time periods are stored in the controller.
6. Correct programming the time values is signalled with several quick blinks of the STATUS LED and going off of ▼, ▲ diodes associated with the specific
shutter.
2. REMOTE PROGRAMMING OF TIME USING EXTA LIFE APPLICATION
• You can configure the opening and closing time for shutters controlled by the SRM-22 controller from the mobile app. To do so, first pair the SRM-22
receiver with the EXTA LIFE system controller. To configure the time periods from the editing menu on the receiver, select „Configure”. Currently used
opening and closing time read from the SRM-22 controller for the shutter are defined by the parameters „Closing time” and „Opening time”. You can
manually change these values in the range from 1 second to 10 minutes.
• The opening / closing time can be also programmed using the mobile application using the „Configure closing / opening time”. This is done in a similar
way as with the PROG button.
To program time for opening and closing, set the shutter in the extreme top position, i.e. fully open.
1. Briefly press the „Configure opening / closing time” button.
2. A screen will be displayed to configure opening / closing time values. During the programming procedure, messages are displayed indicating the status
of the programming.
3. Press the START button and the shutter will start closing and the STATUS LED will start blinking at the same time every 1 s which signals measuring of
the closing time. When the shutter reaches the extreme bottom position, press the START button again. The shutter will start opening and the opening
time will be programmed. When the shutter reaches the extreme top position, press the START button again. This is the end of programming procedure
for opening / closing time. The times are stored in the controller and brought up to the configuration screen for particular channel in the SRM-22.
OPERATING CONSIDERATIONS
SRM-22 RECEIVER FUNCTIONS:
1. The controller allows independent control of two shutters.
2. Each shutter connected to SRM-22 can be controlled simultaneously using the following methods:
2.1 EXTA LIFE system transmitters / external inputs
- local mode control
- central mode control
- calling out up to 2 favourite settings
- with external inputs: control using single or double buttons.
2.2 EXTA LIFE mobile app paired with the controller
- close / open / stop control using control buttons
- using the slider to set the percent value for closing the shutter
- calling out max. 4 favourite settings.
3. The current shutter position is shown in the mobile app (shutter closure % + icon). There are icons for 3 shutter states: fully open, fully closed, intermedi-
ate position.
4. More EXTA LIFE buttons for transmitters may be assigned to a single controller – up to 96 pairs (e.g. 48 receivers in local mode). The number of buttons
refers to the complete controller (both shutters).
5. Transmitters’ buttons can be assigned to the SRM-22 controller using the PROG button and “remotely” using the mobile app (without access to the
controller).
6. Several SRM-22 controllers can work with one transmitter – this allows creating shutter groups (central mode is the recommended operating mode then)
or independent control of shutter from several locations.
7. The shutter controller can be paired with only one EXTA LIFE controller (after pairing the controller is not visible to other controllers).
8. The buttons assigned to the shutter in the SRM-22 controller may be removed selectively.
9. It is also possible to delete all buttons stored in the controller’s memory by performing a factory reset. Buttons assigned to both shutters are deleted
then.
10. Basic parameters for the SRM-22 are configured from the app.
11. You can use the mobile app to perform a remote software update in the controller (for this, you must connect a USB 2.0 memory stick with the latest
SRM-22 software version to the controller).
Default (factory) settings for a SRM-22 – shared between both shutters (shutter 1 and shutter 2):
Parameter
Default settings
Configuration range
Shutter behaviour after activation of supply voltage
Shutter position does not change
Yes – mobile app
Input type LOCAL 1 and LOCAL 2
Spring-action, double shutter buttons
Yes – mobile app or physical connection of
inputs ▼ and ▲ for specific shutter
Operating mode for inputs LOCAL 1 LOCAL 2
Local control ▼ – shutter down ▲ – shutter up
Yes – mobile app
Default shutter movement time
120 s
Yes – mobile app or PROG button
Currently set closing / opening time with
manual entering option
Available values from 1 s to 10 min
Button for configuring
closing / opening time
Field for configuring the first
favourite position
Field for configuring the second
favourite position
Favourite positions
for radio transmitters and local
inputs