Z3 Technology Z3-HE4K-01 Скачать руководство пользователя страница 39

Страница: 39 / 49

DOC-USR-0056-09

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Set Display

(Decode Only)

If a resolution is different from the default is
desired, the user would change to the desired value
and then click the “set Display” button.

Set Device Name

Sets the name for the Z3-HE4K-01.

Set Password

Sets the system password. See Section 9.4, “Using
the Password Feature” on page 31 for more details.

update device firmware

Allows for updating the firmware on the Z3-HE4K-01.

download device logs

Clicking this causes the Z3-HE4K-01 to extract a set
of diagnostic logs that can be sent to Z3 Technology
in the event of an issue to be reported. This file is
saved on the PC which the GUI is being run from.

Note 1: Decode Resolutions supported:

2160p30, 2160p29.97, 2160p25, 2160p24, 2160p23.98, 1080i30, 1080i29.97, 1080i25,

1080p60, 1080p59.94, 1080p50, 720p60, 720p59.94, 720p50, 480p60, 576p50

The User Presets Tab

10.2

Parameter

Options (default in bold)

Notes

new

Define a new configuration file. Up to nine
configurations can be created.

rename

Rename a configuration file.

delete

Delete a configuration file.

export

Export current settings to a file.

import

Load settings from a previously exported file.

Содержание Z3-HE4K-01


















































Результаты поиска

Содержание Z3-HE4K-01

Отзывы:

Похожие инструкции для Z3-HE4K-01

Бренды по названию

Популярные бренды

Z3 Technology Z3-HE4K-01, Инструкция пользователя

Результаты поиска

Содержание Z3-HE4K-01

Отзывы:

Похожие инструкции для Z3-HE4K-01

Бренды по названию

Популярные бренды