Yuria-Pharm ULAIZER HOME CN-02 MY, Руководство пользователя

Страница: 16 / 66

USER’S MANUAL EN EN 28 29
Guidance and manufacturer’s declaration – electromagnetic immunity
The device is intended for use in the electromagnetic environment specified below. The customer or the
user of the device should assure that it is used in such an environment.
Immunity test EN 60601 test level Compliance level
Electromagnetic environ -
ment - guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
±6 KV contact
±8 KV air
±6 KV contact
±8 KV air
Floors should be wood,
concrete or tile. If floors are
covered with synthetic ma -
terial, the relative humidity
should be at least 30%.
Electrical fast t
transient/burst
IEC 61000-4-4
±2 KV for power supply
lines
±2 KV for power supply
lines
Mains power quality should
be that of a typical com -
mercial or hospital envi -
ronment.
Surge IEC 61000-
4-5
±1 KV line(s) and neutral ±1 KV line(s) and neutral Mains power quality should
be that of a typical com -
mercial or hospital envi -
ronment.
Voltage dips,
short
interruptions
and voltage
variations on
power supply
input lines
IEC 61000-4-11
5 % UT
(>95 % dip in UT)
for 0.5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
>5 % UT
(>95 % dip in UT)
for 5s
<5 % UT
(>95 % dip in UT)
for 0.5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
>5 % UT
(>95 % dip in UT)
for 5s
Mains power quality should
be that of a typical com -
mercial or hospital envi -
ronment. If the user of the
device requires continued
operation during power
mains interruptions, it is
recommended that the de -
vice be powered from an
uninterruptible power sup -
ply or a battery.
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
3 A/m 3 A/m Mains power quality should
be that of a typical commer -
cial or hospital
environment.
Note: UT is the a.c. mains voltage prior to application of the test level.
10. EMC INFORMATION
Guidance and manufacturer’s declaration – electromagnetic emissions
The device is intended for use in the electromagnetic environment specified below. The cus -
tomer or the user of the device should assure that is used in such an environment.
Emissions Compliance Electromagnetic environment—guidance
RF emissions CISPR 11 Group 1 The device uses RF energy only for its
internal function. Therefore, its RF emis -
sions are very low and not likely to cause
any interference in nearby electronic
equipment.
RP emissions CISPR 11 Class B
The device is suitable for use in all estab -
lishments, including domestic establish -
ments and those directly connected to the
public low-voltage power supply network
that supplies buildings used for domestic
purposes.
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/ flicker
emissions IEC 61000-3-3
Complies
Recommended separation distances between portable and mobile RF communications equip -
ment and the IH25/1
The IH25/1 is intended for use in an electromagnetic environment in which radiated RF distur -
bances are controlled. The customer or the user of the IH25/1 can help prevent electromagnetic
interference by maintaining a minimum distance between portable and mobile RF communications
equipment (transmitters) and the IH25/1 as recommended below, according to the maximum output
power of the communications equipment.
Rated maximum
output power of
transmitter W
Separation distance according to frequency of transmitter m
150 kHz to 80 MHz
d = 1.2√P
80 to 800 MHz
d = 1.2√P
800 MHz to 2,5 GHz
d = 2.3√P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3,8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in meters (m) can be estimated using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to
the transmitter manufacturer.
Notes:
1. At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
2. These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorp -
tion and reflection from structures, objects and people.