manualshive.com logo in svg

YSI PRO20, Руководство пользователя

Поделиться
Скачать
YSI PRO20 Скачать руководство пользователя страница 17

11

ONE TOUCH CALIBRATION (ONE TOUCH CAL)

One Touch Calibration

 can be enabled or disabled by using the up or 

down arrow keys to highlight 

One Touch Cal

 and pressing enter 

. 

An ‘X’ in the box next to One Touch indicates it is enabled.

When One Touch Cal is enabled, press and hold the calibration 

 key 

for 3 seconds while in the run screen to calibrate Dissolved Oxygen 
to the barometer reading and salinity correction value. For more 
information on One Touch Calibration, see the Calibration section of 
this manual.

AUDIO  

Audio

 can be enabled or disabled by using the up or down arrow keys 

to highlight 

Audio

 and pressing enter. When enabled, there will be an 

‘X’ in the box next to Audio.

When Audio is enabled, the Pro20/Pro20i will beep twice to indicate 
stability when Auto Stable is enabled. The instrument will also beep 
when a key is pressed. When Audio is disabled, the Pro20/Pro20i will 
not beep.

CONTRAST

To adjust the display Contrast, use the up or down arrow keys to 
highlight 

Contrast

, then press enter. Next, use the up or down arrow 

keys to adjust the contrast.  The up arrow key will darken the contrast 
and the down arrow key will lighten the contrast. After adjusting the 
contrast, press enter to save and exit the Contrast adjustment function.   

Alternate Contrast Adjustment Option

If necessary, there is an alternate method of adjusting the contrast. To 
adjust the contrast, press and hold the menu key, then press the up 
arrow key to darken the contrast or press the down arrow key to lighten 
the contrast.  

Содержание PRO20















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды