York YCAL Series Скачать руководство пользователя страница 155

Страница: 155 / 174

FORM 150.66-NM3

ISSUE DATE: 09/25/2020

155

JOHNSON CONTROLS

SECTION 9 - SERVICE AND TROUBLESHOOTING

TABLE 32 – TROUBLESHOOTING (CONT’D)

PROBLEM

CAUSE

SOLUTION

HIGH DISCHARGE PRESSURE FAULT

1. condenser fans not operating or

operating backwards.

1. Check fan motor, fuses and

contactors. Ensure fan blows air

upward.

2. Too much refrigerant.

2. Remove refrigerant.

3. Air in refrigerant system.

3. Evacuate and recharge system.

4. Defective discharge pressure

transducer.

4. Replace discharge pressure

transducer. Refer to “Service”

section for pressure/voltage

formula.

LOW LIQUID TEMP FAULT

1. Improperly adjusted leaving chilled

liquid temp. cutout (glycol only).

1. Re-program the leaving chilled

liquid temp. cutout.

2. Micro panel setpoint/range values

improperly programmed.

2. Re-adjust setpoint/range.

3. Chilled liquid flow too low.

3. Increase chilled liquid flow

– refer to “Limitations” in

“Installation” section.

4. Defective LWT or RWT sensor.

(ensure the sensor is properly

installed in the bottom of the well with

a generous amount of heat conductive

compound).

4. Compare sensor against a

known good temperature

sensing device. Refer to

“Service” section for temp./

voltage table.

MP / HPCO FAULT

1. Compressor internal motor protector

(MP) open.

1. Verify refrigerant charge is not

low. Verify superheat setting of

10° - 15°F (5.6° - 8.3°C). Verify

correct compressor rotation.

Verify compressor is not over

loaded.

2. External overload tripped.

2. Determine cause and reset.

3. HPCO switch open.

3. See “High Press. Disch.” fault.

4. Defective HPCO switch.

4. Replace HPCO switch.

5. Defective CR relay.

5. Replace relay.

COMPRESSOR(S) WON’T START

1. Demand not great enough.

1. No problem. Consult

“Installation” Manual to aid in

understanding compressor

operation and capacity control.

2. Defective water temperature sensor.

2. Compare the display with a

thermometer. Should be within

+/- 2 degrees. Refer to “Service”

section for RWT/LWT temp./

voltage table.

3. Contactor/Overload failure.

3. Replace defective part.

4. Compressor failure.

4. Diagnose cause of failure and

replace.

Содержание YCAL Series















































































































































































Результаты поиска

Содержание YCAL Series

Отзывы:

Похожие инструкции для YCAL Series

Бренды по названию

Популярные бренды

York YCAL Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание YCAL Series

Отзывы:

Похожие инструкции для YCAL Series

Бренды по названию

Популярные бренды