York YCAL Series Скачать руководство пользователя страница 116

Страница: 116 / 174

JOHNSON CONTROLS

116

FORM 150.66-NM3

ISSUE DATE: 09/25/2020

SECTION 7 - UNIT CONTROLS

Programming of the cooling setpoints, daily schedule,

and safeties is accomplished by using the keys located

under the SETPOINTS section.

The three keys involved are labeled COOLING

SETPOINTS, SCHEDULE/ADVANCE DAY, and

PROGRAM.

Following are instructions for programming the respec-

tive setpoints. The same instruction should be used to

view the setpoints with the exception that the setpoint

will not be changed.

Cooling Setpoints

The Cooling Setpoint and Range can be programmed

by pressing the COOLING SETPOINTS key. The

cooling mode (leaving chilled liquid or return chilled

liquid) will be displayed for a few seconds, and the set-

point display entry screen will appear.

SETPOINTS KEYS

00069VIP

Leaving Chilled Liquid Control

S E T P O I N T = 4 5 . 0 ° F
R A N G E = +/- 2 . 0 ° F

The above message shows the current chilled water

temperature SETPOINT at 45.0°F (notice the cursor

positioned under the number 0). Pressing either the ↑

(UP) or ↓ (DOWN) arrow will change the setpoint in

.5°F increments. After using the ↑ (UP) or ↓ (DOWN)

arrow keys to adjust to the desired setpoint, the EN-

TER/ADV key must be pressed to enter this number

into memory and advance to the RANGE SETPOINT.

Entry of the setpoint will be indicated by the cursor

moving under the current RANGE setpoint. The ↑ (UP)

and ↓ (DOWN) arrow keys are used to set the RANGE,

in .5 °F increments, to the desired RANGE setpoint.

After adjusting the setpoint, the ENTER/ADV key

must be pressed to enter the data into memory.

Notice that the RANGE was programmed for plus or

minus X.X° F. This indicates the SETPOINT to be in

the center of the control range. If the control mode has

been programmed for RETURN LIQUID control, the

message below would be displayed in place of the pre-

vious message.

Содержание YCAL Series















































































































































































Результаты поиска

Содержание YCAL Series

Отзывы:

Похожие инструкции для YCAL Series

Бренды по названию

Популярные бренды

York YCAL Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание YCAL Series

Отзывы:

Похожие инструкции для YCAL Series

Бренды по названию

Популярные бренды