York International YCAA B 120 Скачать руководство пользователя страница 67

Страница: 67 / 72

11 DE-COMMISSIONING,

DISMANTLING AND DISPOSAL

Never release refrigerant to the

atmosphere when emptying the

refrigerating circuits. Suitable retrieval

equipment must be used. If reclaimed

refrigerant cannot be re-used. It must be

returned to the manufacturer.

Never discard used compressor oil, as it

contains refrigerant in solution. Return

used oil to the oil manufacturer.

Unless otherwise indicated, the operations described

below can be performed by any properly trained

maintenance technician.

11.1 General

Isolate all sources of electrical supply to the unit

including any control system supplies switched by the

unit. Ensure that all points of isolation are secured in the

'OFF' position. The supply cables may then be

disconnected and removed. For connection points refer

to Section 4.

Remove all refrigerant from each system of the unit into

a suitable container using a refrigerant reclaim or

recovery unit. This refrigerant may then be re-used, if

appropriate, or returned to the manufacturer for

disposal. Under NO circumstances should refrigerant

be vented to atmosphere. Drain the refrigerant oil from

each system into a suitable container and dispose of

according to local laws and regulations governing the

disposal of oily wastes. Any spilt oil should be mopped

up and similarly disposed of.

Isolate the unit heat exchanger(s) from all external water

systems and drain the heat exchanger section(s) of the

system. If no isolation valves are installed it may be

necessary to drain the complete system(s).

If glycol or similar solutions have been

used in the water system(s), or chemical

additives are contained, the solution

MUST be disposed of in a suitable and safe

manner. Under NO circumstances should

any system containing glycol or similar

solutions be drained directly into domestic

waste or natural water systems.

After draining, the water pipework can be disconnected

and removed.

Packaged units can generally be removed in one piece

after disconnection as above. Any fixing down bolts

should be removed and then the unit should be lifted

from position using the points provided and equipment

of adequate lifting capacity.

Reference should be made to Section 4 for unit

installation instructions, Section 9 for unit weights and

Section 3 for handling.

Units which cannot be removed in one piece after

disconnection as above, must be dismantled in position.

Special care should be taken regarding the weight and

the handling of each component. Where possible units

should be dismantled in the reverse order of installation.

Residual refrigerant oil and glycol or

Содержание YCAA B 120









































































Результаты поиска

Содержание YCAA B 120

Отзывы:

Похожие инструкции для YCAA B 120

Бренды по названию

Популярные бренды

York International YCAA B 120, Инструкция по установке, пусконаладке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание YCAA B 120

Отзывы:

Похожие инструкции для YCAA B 120

Бренды по названию

Популярные бренды