York International YCAA B 120 Скачать руководство пользователя страница 22

Страница: 22 / 72

4.7

Electrical Supplies

Ensure that the power supply is off before

working on the electrical system.

The unit must be provided with an earth

connection.

It is the installers responsibility to ensure that

all external wiring complies with applicable

safety regulations.

York is not responsible for injury or damage of any

kind resulting from failure to observe these

precautions.

The unit complies with EN 60 439-1 of 1998.

The following connections are required:

One three-phase line and earth for the power

circuit supply.

The electrical distribution system must be able to supply

all the unit power, refer to Section 9.

The disconnect switches and circuit breakers must be

sized to handle the unit starting current, refer to

Section 9.

Supply and isolating devices shall be designed so that

the lines are fully independent.

Magnetic thermal differential breakers are

recommended, to prevent damage due to electrical

phase loss.

Power supplies to the compressors and the fans are

through contactors controlled by the control panel.

Each motor is provided with an internal thermal overload

cut-out and external fuses.

Supply cables should be routed through the cable

entries on the unit front and enter the electrical panel

through a hole at the bottom of the panel.

4.8

Electrical Connections

The installation of the unit on the final site must be

carried out according to the Machinery Safety

Directive (98/37/EC), to the Low Voltage Directive

(73/23/EEC), to the Electromagnetic Interference

Directive (89/336/EEC) as modified by Directive

(92/31/EEC) and according to normal rules for

technical matters prescribed by the applicable

country regulations. Do not operate the unit before

having observed all the above. Supply lines shall

consist of insulated copper conductors sized for

maximum current draw.

Terminal connections should be made in accordance

with the connection diagram in this manual and the

diagram supplied with the unit.

Before connecting the supply lines, check that

the mains voltage is within the range shown in

the Electrical Data in Section 9.

For the 3 phase power supply, also check that the phase

unbalance does not exceed 2%. The check is

performed by measuring the difference between the

voltage of each phase pair and the average mains

voltage during operation. The maximum measured

difference (unbalance) shall not exceed 2% of the

average voltage.

If the unbalance is unacceptable, the electricity supply

company must be asked to correct the fault.

Supplying the unit with a line whose

unbalance exceeds the specified value will

automatically void the warranty.

(09/03)

035B09012-100 Rev. 4

Содержание YCAA B 120









































































Результаты поиска

Содержание YCAA B 120

Отзывы:

Похожие инструкции для YCAA B 120

Бренды по названию

Популярные бренды

York International YCAA B 120, Инструкция по установке, пусконаладке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание YCAA B 120

Отзывы:

Похожие инструкции для YCAA B 120

Бренды по названию

Популярные бренды