YOKOGAWA YTA710 Скачать руководство пользователя страница 27

Страница: 27 / 44

<4. Self-Diagnostics>

4-2

IM 01C50T03-02EN

Table 4.1

Alarm List

Indicator

display

BRAIN configuration

tool display

Cause

Output operation

upon error

Action

AL.00

CPU Failure

The main CPU has failed.

Data output and

communication do not

occur if the transmitter

has failed.

Device Replacement

AL.01

Snsr NV Failure

CRC mismatching of the

sensor's non-volatile memory

has occurred, or normal data

wiring has failed.

Data output and

communication

are permitted if the

transmitter has failed.

AL.02

Temp NV Failure

CRC mismatching of TEMP

ASSY non-volatile memory has

occurred, or Write/Read Verify

mismatching has occurred.

(System cannot start up

normally.)

AL.03

AD Conv Failure

Hardware failure at input side

AL.04

Main R-Calc Fail

Mismatching of MAIN ASSY

CPU inverse computation has

occurred.

AL.05

Temp R-Calc Fail

Mismatching of TEMP ASSY

CPU inverse computation has

occurred.

AL.06

Temp Volt Fail

Abnormal TEMP ASSY power

voltage

AL.07

Comm NV Fail

CRC mismatching of

communication non-volatile

memory has occurred, or

normal data wiring has failed.

AL.08

Temp NV Warning

CRC mismatching of TEMP

ASSY non-volatile memory has

occurred, or Write/Read Verify

mismatching has occurred.

(System can start up but may

fail.)

The output continues.

AL.09

Int Comm Fail

Internal communication error

The output and

communication for

sensor burnout are

permitted.

AL.10

S1 Failure

The Sensor1 input circuit is

open or disconnected from the

terminal.

See Table 4.2.

• Check the

soundness of the

temperature sensor.

• Check the sensor

connection.

AL.11

S2 Failure

The Sensor2 input circuit is

open or disconnected from the

terminal.

AL.12

S1 Short

Sensor1 has shorted.

AL.13

S2 Short

Sensor2 has shorted.

AL.14

S1 Corrosion

Sensor1 has corroded.

Normal operation

Check the sensors,

terminals, and cables.

AL.15

S2 Corrosion

Sensor2 has corroded.

Normal operation

AL.20

S1 Signal Error

The Sensor1 input has error

Normal operation

• Check the

soundness of the

temperature sensor.

• Check the sensor

type.

AL.21

S2 Signal Error

The Sensor2 input has error

Normal operation

AL.22

Term Sensor Fail

The terminal block temperature

is abnormal. The terminal block

temperature sensor has failed,

or its circuit is open.

See Table 4.2.

Device Replacement

Содержание YTA710













































Результаты поиска

Содержание YTA710

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA YTA710, Руководство пользователя

Результаты поиска

Содержание YTA710

Отзывы:

Бренды по названию

Популярные бренды