YOKOGAWA Vigilantplant IR200 Скачать руководство пользователя страница 14

Страница: 14 / 103

3 - 1

IM 11G02M01-01E

3. INSTALLATION

DANGER

CAUTION

This unit is not explosion-proof type. Do not use it in a place with explosive gases to prevent

explosion, fire or other serious accidents.

• For installation, observe the rule on it given in the instruction manual and select a place

where the weight of gas analyzer can be endured.
Installation at an unsuited place may cause turnover or fall and there is a risk of injury.

• For lifting the gas analyzer, be sure to wear protective gloves. Bare hands may invite an

injury.

• Before transport, fix the casing so that it will not open. Otherwise, the casing may be sepa-

rated and fall to cause an injury.

• The gas analyzer is heavy. It should be transported carefully by two or more persons if

manually required. Otherwise, body may be damaged or injured.

• During installation work, care should be taken to keep the unit free from cable chips or other

foreign objects. Otherwise, it may cause fire, trouble or malfunction of the unit.

3.1 Selection of installation location

To install the analyzer for optimum performance, select a location that meets the following conditions;

(1) Use this instrument indoors.

(2) A vibration-free place

(3) A place which is clean around the analyzer.

(4) Power supply

Voltage rating

;100 V AC to 240 V AC

Allowable range

; 85 to 264 V AC

Frequency

; 50 Hz / 60 Hz

Power consumption; 70 VA max.

Inlet

; Conform to EN60320

Protection Class 1

(5) Operation conditions

Ambient temperature

: -5 to 45

Ambient humidity

: 90% RH or less, no condensation

Содержание Vigilantplant IR200








































































































Результаты поиска

Содержание Vigilantplant IR200

Отзывы:

Похожие инструкции для Vigilantplant IR200

Бренды по названию

Популярные бренды

YOKOGAWA Vigilantplant IR200, Руководство пользователя

Результаты поиска

Содержание Vigilantplant IR200

Отзывы:

Похожие инструкции для Vigilantplant IR200

Бренды по названию

Популярные бренды