YOKOGAWA ROTAMETER RAMC Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 49

YOKOGAWA ROTAMETER RAMC Скачать руководство пользователя страница 6

3. INSTALLATION

3-1

All Rights Reserved. Copyright © 2006, Rota Yokogawa

IM 01R01B02-01E-E 5th edition October 01, 2020 -00

3.1 Wiring System Configuration

The number of devices that can be connected to a single bus and the cable length vary depending on
system design. When constructing systems, both the basic and overall design must be carefully considered

to allow device performance to be fully exhibited.

3.2 Connection of Devices

The following instruments are required for use with PROFIBUS PA devices:

• Terminator:

PROFIBUS PA requires two terminators at the end of the segment

• Segment Coupler:

PROFIBUS PA requires the segment coupler which adopts to the RS-485 signals to the IEC 61158-2
signal level.

• Field devices:

Connect RAMC PROFIBUS PA communication type. Two or more RAMC devices or other devices can
be connected.

• Master:

     Used for accessing field devices. A dedicated master (such as DCS or PLC) is used for an instrumentation
  line while dedicated communication tools are used for experimental purposes. For operation of the
  master, refer to the instruction manual for each master. No details of the master are explained in the

rest of this manual.

•

Cable:

NOTE

The PROFIBUS specification must be regarded.

Two-core twisted and shielded cables are recommended, otherwise the EMC-requirements for

industrial flow meters can not be guaranteed.

EN 50170 specifies two types of bus cables. For transmission rates up to 1.5 Mbit/s, cable type A is

recommended.

3. Installation

Figure 3.1 Device Connection

+
–

+
–

Field Instrument

Field Instrument

Terminator

RAMC

-

-

P

429

PR

OFIBUS

PA

PR

OFIBUS DP

Segment
coupler

Grounding:
1) Device
2) Cable shield on bus side
3) Cable shield on transmitter side recommended

3)

2)

1)

It is recommended to connect the shield on both
sides to ground. Compensation currents on ground
lines must be avoided. Therefore the shield may be
connected to ground on one side (e.g. in control
cubicle) via capacitor to ground.

The potential equalization must be connected

to the flow meter.

If the shield is only connected on supply side,
reduction of EMC immunity is possible.

NOTE

In case of insufficient cable shielding and

grounding, degrading of EMC immunity is

possible.

«
...
4
5
6
7
8
...
»

Содержание ROTAMETER RAMC


















































Отзывы:

Нет отзывов