YOKOGAWA DL 1540 Скачать руководство пользователя страница 180

Страница: 180 / 201

IM 701510-01E

16-6

16.7 Communication Interface

For details regarding the GP-IB/RS-232-C interface, refer to the “Communication Interface User’s Manual” (IM 701510-11E).

GP-IB Interface

Comes standard on DL1540/DL1540L. Provided with DL1520/DL1520L with suffix code -
C1, -C3, or -C4.

Item

Specifications

Interface

GP-IB

Electrical and mechanical

Conforms to IEEE St’d 488-1978 (JIS C 1901-1987).

specifications

Interface function

SH1, AH1, T5, L4, SR1, RL1, PP0, DC1, DT0, C0

Protocol

Conforms to IEEE St’d 488.2-1987.

Code

ISO (ASCII) code

Mode

Addressable mode/talk-only mode

Address setting

Listener and talker addresses 0 to 30 are settable.

Remote mode clear

Remote mode can be cleared by pressing the LOCAL key (except when local lock-out has been set).

RS-232-C Interface

An optional RS-232-C unit is required for DL1540/DL1540L. This interface is provided
with DL1520/DL1520L with suffix code -C2.

Item

Specifications

Connector type

Half pitch interface cable (DDK : DHA-RB50-S132)

Electrical specifications

Conforms to EIA RS-232-C Standard.

Connection format

point to point

Communication format

full duplex

Synchronizing format

Start-stop asynchronous transmission

Baud rate

75/ 150/ 300/ 600/ 1200/ 2400/ 4800/ 9600/ 19200

Centronics Interface

Provided with DL1520/DL1520L with suffix code -C3. This interface is not supported by
DL1540/DL1540L.

Item

Specifications

Connector type

Centronics interface connector (half-pitch 36 pin), with a printer connecting cable to D-sub socket.

Electrical specifications

Conforms to Centronics specifications.

Printers which support

ESC/P, LIPS, PCPR201 or PCL5

SCSI (Small Computer System Interface)

Provided with DL1520L with suffix code -C4. DL1540/DL1540L with software (ROM)
version 1.20 or later needs the SCSI interface unit 700930 (sold separately). Not provided
with DL1520.

tem

Specifications

Interface standard

Conforms to ANSI X3.131-1986 for SCSI (Small Computer System Interface)

Connector shape

Half pitch 50 pins (Converting to the pin type is possible with the SCSI adapter accessory)

Electrical specifications

Single end, refer to Section 3.3 for pin configurations.

SCSI Devices that can be Used*

HD Drives

: SCSI HD drives for MS-DOS ver.3.3 or later, or SCSI HD drives that can format in
EZ-SCSI.

MO Drives

: 128/230/640 MB drives. MO media uses Semi IBM format.

ZIP Drives
PD Drives

* SCSI devices which can send and receive data over SCSI and which can set the ID number to "5" can be used. There are exceptions as

in the case when the media used on the SCSI device is formatted with another equipment such as a PC, or the pin configuration of the

connector is different. The specifications of each SCSI device are shown above. For more detailed information, contact your nearest

YOKOGAWA representative listed on the back cover of this manual.

Содержание DL 1540










































































































































































































Результаты поиска

Содержание DL 1540

Отзывы:

Похожие инструкции для DL 1540

Бренды по названию

Популярные бренды

YOKOGAWA DL 1540, Руководство пользователя

Результаты поиска

Содержание DL 1540

Отзывы:

Похожие инструкции для DL 1540

Бренды по названию

Популярные бренды