manualshive.com logo in svg

YOKOGAWA Daqstation DX1000N, Руководство пользователя, Страница: 5 / 75

Поделиться
Скачать
YOKOGAWA Daqstation DX1000N Скачать руководство пользователя страница 5

4

IM 04L41B01-02E

WARNING

• Use the Correct Power Supply

Ensure that the source voltage matches the voltage of the power
supply before turning ON the power.  In the case of a desktop
type, ensure that it is within the maximum rated voltage range of
the provided power cord before connecting the power cord.

• Use the Correct Power Cord and Plug (Desktop Type)

To prevent electric shock or fire, be sure to use the power cord

supplied by YOKOGAWA.  The main power plug must be
plugged into an outlet with a protective earth terminal.  Do not

disable this protection by using an extension cord without
protective earth grounding.

• Connect the Protective Grounding Terminal

Make sure to connect the protective grounding to prevent

electric shock before turning ON the power.
The power cord that comes with the desktop type is a three-

prong type power cord.  Connect the power cord to a properly
grounded three-prong outlet.

• Do Not Impair the Protective Grounding

Never cut off the internal or external protective grounding wire or

disconnect the wiring of the protective grounding terminal.
Doing so invalidates the protective functions of the instrument

and poses a potential shock hazard.

• Do Not Operate with Defective Protective Grounding

Do not operate the instrument if the protective grounding might
be defective.  Also, make sure to check them before operation.

• Do Not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable

liquids or vapors.  Operation in such an environment constitutes
a safety hazard.

Prolonged use in a highly dense corrosive gas (H

2

S, SOx, etc.)

will cause a malfunction.

• Do Not Remove Covers

The cover should be removed by YOKOGAWA’s qualified

personnel only.  Opening the cover is dangerous, because
some areas inside the instrument have high voltages.

• Ground the Instrument before Making External Connections

Connect the protective grounding before connecting to the item

under measurement or control unit.

• Damage to the Protection

Operating the instrument in a manner not described in this
manual may damage the instrument’s protection.

•

Exemption from Responsibility

• YOKOGAWA makes no warranties regarding the product except

those stated in the WARRANTY that is provided separately.

• YOKOGAWA assumes no liability to any party for any loss or

damage, direct or indirect, caused by the user or any
unpredictable defect of the product.

•

Handling Precautions of the Software

• YOKOGAWA makes no warranties regarding the software

accompanying this product except those stated in the
WARRANTY that is provided separately.

• Use the software on a single PC.
• You must purchase another copy of the software, if you are to

use the software on another PC.

• Copying the software for any purposes other than backup is

strictly prohibited.

• Please store the original media containing the software in a safe

place.

• Reverse engineering, such as decompiling of the software, is

strictly prohibited.

• No portion of the software supplied by YOKOGAWA may be

transferred, exchanged, or sublet or leased for use by any third
party without prior permission by YOKOGAWA.

Handling Precautions of the DX

• Use care when cleaning the DX, especially any plastic parts.

When cleaning, wipe using a dry soft cloth.  Do not use

chemicals such as benzene or thinner, since these may cause
discoloring and deformation.

• Keep electrically charged objects away from the signal

terminals.  If you do, the DX may malfunction.

• Do not apply volatile chemicals to the display, panel keys, etc.

Do not allow rubber and vinyl products to remain in contact with

the DX for long periods of time.  If you do, the DX may
malfunction.

• When not in use, make sure to turn OFF the power switch.
• If there are any symptoms of trouble such as strange odors or

smoke coming from the DX, immediately turn OFF the power
switch and the power supply source.  Then, contact your

nearest YOKOGAWA dealer.

Handling Precautions of the External Storage
Medium (CF Card)

• Use caution in the handling of the external storage medium as it

is a delicate product.

• Write operation to storage media may fail under high-

temperature or low-temperature environments.  If you are using
the DX in a low-temperature environment (around 10 

°

C or

less), use the DX after the warm-up time (at least 30 minutes)
has elapsed.  If you are using the DX under a high-temperature

environment (around 40 

°

C or more), it is recommended that the

external storage medium be inserted into the drive when saving

the data and be removed after the data storage operation is
finished.

• Remove the storage medium from the drive when turning the

DX ON/OFF.

• Touching the compact flash section when static electricity is built

up on the human body can lead to erroneous operation.

• For the general handling precautions of the external storage

medium, see the instruction manual that came with the external

storage medium.

CAUTION

• Do not eject the external storage medium while the access

indicator is illuminated.  This can damage the data.

• Do not access the storage medium in a place with vibrations or

shock.  The storage medium or drive may malfunction.

Содержание Daqstation DX1000N












































































Отзывы:

Нет отзывов