UNIT OPERA
TION
UNIT OPERA
TION
P17 OF 36
P18 OF 36
YMGI, Engineered Comfort Products for A Sustainable and Efficient Green World !
YMGI, Engineered Comfort Products for A Sustainable and Efficient Green World !
Once the U-TOUCH stars appear, the remote will send a signal of the remote-local temperature to the indoor unit,
and this remote-local temperature will supersede the return air temperature as the unit's target temperature.
Every 10 minutes such signal will be sent from the remote to the indoor unit updating the remote-local
temperature. If at any time during this process no signal is received by the indoor unit from the remote, the unit
will switch back to the previously set temperature before the U-TOUCH feature is activated. To turn the U-
TOUCH feature off, simply press the U-TOUCH button until you see the symbol disappear from the remote
screen. By doing so, the return air temperature will take place of remote-local temperature as the unit's target
temperature. U-TOUCH is what YOU WANT. U-TOUCH feature brings to you a true comfort level wherever and
whenever you want.
REMOTE CONTROL-BUTTON NAME & FUNCTIONS
"SWING" BUTTON:
Hold the swing button (symbol
shown above) for more than 2 seconds and the
indoor air louver will start to swing between the
highest and lowest limits. Once the swing button is
released the louver will stay in the last position where
the button was released.
If the swing button is pushed just once the swing icon
will appear on the remote and the louver will swing
up and down continuously between the highest and
lowest points. Push the swing button once more and
the icon will disappear on the remote and the louver
will remain at the last point the button was pushed.
When the unit is powered off by the remote the louver
will close on the indoor unit.
Press this button to set up the desired swing angle
which circularly changes as below. (Insert swing
picture)
"U-TOUCH" BUTTON:
Since the indoor unit is normally mounted high up on the wall or attached to the ceiling, the
temperature at where the return air sensor is installed inside the indoor unit is higher than what it is where the
area people stand and can feel (4 to 7 feet above the floor). If the unit uses the return air temperature as its
target control, people may feel colder than what they really want (target) in both cooling mode and heating mode.
The facts of air stratification and warm air rising and cold air dropping require users to set up, by experiments or
experience, the target temperature quite few degrees higher than what you really want , in order to reach a
satisfied or more precise indoor comfort. This is a common drawback of AC/HP units made by other manufacturers.
With YMGI's U-touch feature, this can be avoided and your comfort level can be improved.
When you press the U-TOUCH button on the remote control, the unit will use the temperature where the remote
is located as its target temperature control. Once you do so, you will notice a figure of a person surrounded by
stars appear on the remote.
"SWING UP AND DOWN" BUTTON
Press this button, to set up swing angle,
circularly changes as below:
which
This is an universal use remote control. If remote
control sends the following three kinds of status
that the swing status of main unit will be:
When the guide louver start to swing up and down, if
turn off the Swing, the air guide louver will stop at
current position.
which indicates the guide louver swings up and
down between that all five positions.
H1
T
H2
Warmer
Colder
Warm air rises
Cold air drops
T+
△
Temp sensor
Wall mount indoor unit
"U-Touch" Feature Is Activated:
"U-Touch" Feature Is NOT Activated:
Roof
Floor
Signal (communication)
Remete control
(Temp sensor)
T
H1
T
Roof
Floor
(Feel More
Comfortable)
(May Feel Colder than
You Want in Summer
and Winter)
REMOTE CONTROL-BUTTON NAME & FUNCTIONS
SYMBOL DISPLAY
When power is first applied to the unit but the power has not been turned on by the remote control, then the red
power light only is displayed. When the unit has been powered on by the remote control then the running LED is
lit and the current running mode symbol is displayed at the same time.
COOLING:
Running symbol and cooling symbol are lit.
HEATING:
Running lamp and heating symbol are lit.
DRY:
Running lamp and dry lamp are lit
FAN:
Running lamp and fan lamp are lit.
AUTO:
Auto lamp, running lamp and actual running mode are lit.
ALPHA NUMERIC DISPLAY
O
O
*
The setting temperature range for the unit is 61 to 86 F.
O
O
* Under AUTO mode unit will display 77 F for cooling and 68 F for heating modes.
GUIDE FOR OPERATION- GENERAL
OPERATION
1) After powered on, press ON/OFF button, the unit
will start to run.(Note: When it is powered off, the
guide louver of main unit will close automatically.)
2) Press MODE button, select desired running mode,
or press COOL or HEAT mode to enter into the
corresponding operation directly.
3) Pror - button, to set the desired
temperature. (It is unnecessary to set the temp. at
AUTO mode.)
4) Pressing FAN button, set fan speed, can select
AUTO FAN, LOW, MED, and HIGH.
5) Pressing button, to select the swing.
OPERATION OF REMOTE CONTROL
①
②
③
④
①
②
③
④
⑤
