YIC Technologies EMScanner Скачать руководство пользователя страница 3

Страница: 3 / 70

www.yictechnologies.com

About the EMScanner Products

EMScanners product family provides board-level design teams with world-leading fast
nearfield magnetic data to help diagnose EMC design issues.

EMScanner product line consists of

EMScanner, EMS

and

EMProbe

, these

instruments

capture and display visual images of spectral and spatial scan results in seconds. This

allows the design team to immediately analyze and compare design iterations.

PCB designers can scan any board to identify both constant and time-based emission

sources in the range of 150 kHz to 8 GHz.

EMScanner

consists of a patented scanner and a compact adaptor, a customer-supplied

spectrum analyzer and a PC running

EMViewer

software. Free Keysight IO software

application must also be installed on the customer-supplied PC. The patented scanner

consists of an array of 1,218 H-field (magnetic) probes spaced every 7.5 mm which provides
an effective 3.75 mm resolution. The system operates from 150 kHz to 4 GHz and from 150
kHz to 8 GHz with upgradable and optional software license key.

EMScannerR

+ is a self-contained high resolution near-field scanning device. Simply

connect the

EMS

to the PC and to a spectrum analyzer, install the

EMViewer

software on the PC and begin measurements. The system operates from 150 kHz to 8 GHz.

The

EMS

provide 0.06 mm incremental measurement steps.

EMProbe

is a repeatable high resolution EMC and EMI diagnostic with hand held hear field

probes. Different types of Robotic Arms can be used, based on the desired size and
resolution.

Minimum System Requirements



CPU 333 MHz or faster



256 MB RAM recommended



8 MB Video or more



Windows 10 OS



10/100/1000 LAN port



1 or 2 USB1.0 or USB 2.0 ports

Содержание EMScanner







































































Результаты поиска

Содержание EMScanner

Отзывы:

Похожие инструкции для EMScanner

Бренды по названию

Популярные бренды

YIC Technologies EMScanner, Руководство пользователя

Результаты поиска

Содержание EMScanner

Отзывы:

Похожие инструкции для EMScanner

Бренды по названию

Популярные бренды