YATO YT-82360, Инструкция по эксплуатации

Страница: 19 / 124

19
EN
O R I G I N A L I N S T R U C T I O N S
Take regular breaks during operation, checking the condition of the sanding sheet and the fi ll-up level of the dust extraction sys-
tem. If a sanding sheet is found to have been clogged with dust generated during operation, or that the abrasive grain has worn,
replace the sheet with a new one.
Battery storage
Ensure proper storage conditions to extend the battery’s life. The battery can last for approximately 500 charge-discharge cycles.
Store the battery at a temperature ranging from 0ºC to 30ºC at the relative air humidity of 50%. Charge the battery to approx. 70%
of its total capacity to store it for a longer period of time. In case of prolonged storage, the battery should be periodically charged
once a year. Do not over-discharge the battery as this will shorten its life and may cause irreparable damage.
During storage, the battery will gradually discharge due to leakage. The self-discharge process depends on the storage tempera-
ture – the higher the temperature is, the faster the discharge process is. If the batteries are stored incorrectly, the electrolyte may
leak. In case of leakage, secure the leak with a neutralising agent. In the case of electrolyte contact with eyes, rinse eyes thor-
oughly with water, and immediately seek medical attention. It is not allowed to use the tool with a damaged battery. If the battery
is completely worn, return it to a specialist waste disposal centre.
Transport of batteries
Lithium-ion batteries are treated as hazardous materials, according to legal regulations. The user of the tool can transport the
product together with the battery and the batteries alone, by land. In that case, no additional conditions have to be met. If you en-
trust transport to third parties (e.g. a courier company), follow the regulations regarding the transport of hazardous goods. Before
shipping, please contact a properly quali fi ed person. It is not allowed to transport damaged batteries. For the duration of transport,
remove the demountable batteries from the product and secure the exposed contacts, e.g. by covering them with insulation tape.
Protect the batteries in the packaging in such a way that they do not move inside the packaging during transport. National regula-
tions for the transport of hazardous materials must also be observed.
Charging the battery
Caution! Before charging, disconnect the power unit from the mains by removing the plug from the mains socket. In addition,
remove any dirt and dust from the battery and battery clamps with a soft, dry cloth.
The battery has a built-in charge indicator. The LEDs will light up by pressing the button. The more of them come on, the more
charged the battery is. If the LEDs do not light up when the button is pressed, the battery is discharged.
Disconnect the battery from the tool.
Slide the battery into the charger socket (X).
Plug the charger into a mains socket.
The red LED will light up, which indicates the charging process.
When charging is complete, the red LED will turn o ff and the green LED will light up to indicate that the battery is fully charged.
Pull the power unit plug out of the mains socket.
Pull the battery out of the charging station by pressing the battery clamp button.
Caution! If the green LED lights up when the charger is connected to the mains, the battery is fully charged. In this case, the
charger will not start the charging process.
PRODUCT MAINTENANCE
CAUTION! Disconnect the battery before carrying out any adjustment, servicing or maintenance work.
The disc head allows to remove the disc to clean the space between the disc and the drive guard thoroughly. Hold the disc with
your hand, then use the wrench to loosen the disc retaining screw (IX). Clean the space between the disc, the disc itself and the
guard of dust and other contaminants with a soft dry cloth, a jet of compressed air at a maximum pressure of 0.3 MPa, or a soft
brush. Do not use sharp objects for cleaning.
Having fi nished working, check the device for damage by visually inspecting the exterior and the body and the handle, the func-
tioning of the electric switch, the vents for clogging, the motor brushes for sparking, the noise level of the bearings and the drive
transmission, and how the device starts and runs. During the warranty period, the user is not allowed to install any power tools or
replace any components or parts, as this will void the warranty rights. Any irregularities found during the inspection or the opera-
tion signal the need for repair to be done at the service centre. After fi nishing work, the housing, ventilation openings, switches,
auxiliary handle and covers should be cleaned e.g. with an air jet (with a pressure not exceeding 0.3 MPa), paintbrush or dry cloth
without the use of chemicals and cleaning agents. Clean the tools and handles with a dry, clean cloth.