manualshive.com logo in svg

YASKAWA SI-EP3/V, Техническое руководство

Поделиться
Скачать
YASKAWA SI-EP3/V Скачать руководство пользователя страница 7

1  Preface and Safety

7

 

YASKAWA

 SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V  Technical Manual

„

Option Unit Warning Labels

Warning information is displayed on the option unit as shown in the figure below. Follow all warnings and safety 
instructions when using the product.

„

Warning Contents

NOTICE

Do not expose the drive or option to halogen group disinfectants.

Failure to comply may cause damage to the electrical components in the option. 
Do not pack the drive in wooden materials that have been fumigated or sterilized.
Do not sterilize the entire package after the product is packed.

Do not modify the drive or option circuitry.

Failure to comply could result in damage to the drive or option and will void warranty. 
Yaskawa is not responsible for any modification of the product made by the user. 
This product must not be modified.

Lire le manuel avant l'installation.
Attendre  5 minutes apres la coupure de l'alimentation,
pour permettre la decharge des condensateurs.
Pour repondre aux exigences      , s assurer que le
neutre soit relie a la terre, pour la serie 400V. 

AVERTISSEMENT

Lire le manuel avant l'installation.
Attendre  5 minutes apres la coupure de l'alimentation,
pour permettre la decharge des condensateurs.
Pour repondre aux exigences      , s assurer que le
neutre soit relie a la terre, pour la serie 400V. 

WARNING

Read manual before installing.
Wait 5 minutes for capacitor discharge after
disconnecting power supply.
To conform to  

ޓ

  requirements, make sure

to ground the supply neutral for 400V class.  

Risk of electric shock.

Risque de decharge
electrique.

Содержание SI-EP3/V






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды