manualshive.com logo in svg

YASKAWA SI-EP3/V, Техническое руководство

Поделиться
Скачать
YASKAWA SI-EP3/V Скачать руководство пользователя страница 37

8  Communication

37

 

YASKAWA

 SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V  Technical Manual

PROFIdrive Profile-Specific Parameters

PROFIdrive parameters contain data of the drive in standard form. The table below describes the supported PROFIdrive 
parameters. 

Fault Buffer Mechanism

PROFIdrive profile has a mechanism that can store five fault situations to PROFIdrive parameters. Fault and diagnostic 
data, like fault number and fault code can be accessed simultaneously with only one subindex. The mechanism consists of 
two PROFIdrive parameters: 

• PNU944: Fault message counter
• PNU947: Fault numbers according to value in U2-01

‹

Option High Priority Alarm Codes

These codes are transmitted as Manufacturer Specific Diagnostic high priority alarms that can be seen in the PLC 
configuration software. These high priority codes are the same codes that appear in the drive manual, except with an 
offset of 0x1000.

Table 24  PROFINET Option High Priority Alarm Codes

Parameter 

R/W

Data type 

Description 

922 R 

Unsigned16 

Telegram 

selection 

944 

R 

Unsigned16 

Fault message counter 

947 

R 

Array [5] Unsigned16 

Fault number. (coded according to DRIVECOM profile) Subindex Contents, see 
parameter 945. 

964 

R 

Array [6] Unsigned16 

Device identification Subindex Contents 0 Manufacturer 1 Device type 2 Version 3 
Firmware date (year) 4 Firmware date (day/month) 5 Number of Drive Objects (DO) 

965 

R 

Octet String2 

Profile number of this device. 0328h = Profile 3, Version 40 

967 R 

Unsigned16 

Control 

word 

(CW) 

968 

R 

Unsigned16 

Status word (SW) 

972 R/W 

Unsigned16 

Software reset Value Description 0 No action 1 Power-cycle PROFINET IO module 
The parameter must do a zero-to-one transition and the motor must be stopped. 

977 R/W 

Unsigned16 

Stores parameters to non-volatile memory Value Description 0 No action 1 Stores 
parameters The parameter must do a zero-to-one transition and the motor must be 
stopped.

61000 R 

VisibleString24  Name 

of 

station 

61001 

R 

Unsigned32 

IP of station 

61002 

R 

Array [6] Unsigned8 

MAC of station 

61003 R 

Unsigned32 

Default 

gateway of station 

61004 

R 

Unsigned32 

Subnet mask of station 

Drive Alarm 

Code

 (hex)

<1>

Description

Corrective Action

1000

None

-

1001

DC Bus Fuse Open (PUF)

Output Transistor Failure. Replace the drive

1002

DC Bus Undervolt (Uv1)

Input power fluctuation too large

1003

CTL PS Undervolt (Uv2)

Cycle drive power and replace drive if fault continues

1004

MC Answerback (Uv3)

Cycle drive power and replace drive if fault continues

1005

Short Circuit (SC)

• Check drive wiring
• Cycle drive power and replace drive if fault continues.

1006

Ground Fault (GF)

Check for motor and/or cable damage

1007

Over Current (oC)

Check motor, motor load and accel/decel rates

1008

DC Bus Overvolt (oV)

• Check incoming voltage
• Check deceleration time

Содержание SI-EP3/V






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды