YASKAWA SI-EP3/V Скачать руководство пользователя страница 23

Страница: 23 / 53

6 Option Drive Parameters

YASKAWA

SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V Technical Manual

Table 7 Option Monitors

F7-23 to F7-

<5>

Dynamic Output Assembly
Parameters

Configurable outputs 1 to 5.

F7-33 to F7-

<5>

Dynamic Input Assembly
Parameters

Configurable inputs 1 to 5.

H5-11

Communications ENTER
Function Selection

Select the function for the ENTER command that saves parameter data to
the drive.
0: Parameter changes are activated when ENTER command is written
1: Parameter changes are activated immediately without use of ENTER
command

<1> To start and stop the drive with the option master device using serial communications, set b1-02 to 3. To control the drive frequency reference

via the master device, set b1-01 to 3.

<2> If F6-01 is set to 3, then the drive will continue to operate when a bUS error or an EF0 fault is detected. Take proper safety measures, such as

installing an emergency stop switch.

<3> Software versions 1012 and later have F6-07 and F6-08 both set to 1.

<4> Software versions 1014 and earlier have F7-14 default of 0.

<5> If a value other than 0 is assigned to parameters F7-23 to F7-27 and F7-33 to F7-37 by the drive, that value will take precedent over a value set

by the configuration software. If the value in the drive is 0 (default), the value from the configuration software is used.

No.

Name

Description

Value Range

U6-80 to U6-83

Online IP Address

SI-EP3/V IP Address, U6-80 is the most significant octet.

0 to 255

U6-84 to U6-87

Online Subnet

Subnet, U6-94 is the most significant octet.

0 to 255

U6-88 to U6-91

Online Gateway

Gateway, U6-88 is the most significant octet.

0 to 255

U6-92

Online Speed

Port 1 Link Speed

10, 100

U6-93

Online Duplex

Port 1 Duplex Setting

0: Half, 1: Full

U6-94

Online Duplex

Port 2 Link Speed

0: Half, 1: Full

U6-95

Online Duplex

Port 2 Duplex Setting

0: Half, 1: Full

U6-98

First Fault

First Option Board Fault

U6-99

Current Fault

Current Option Board Fault

No.

Name

Description

Default

Содержание SI-EP3/V






















































Результаты поиска

Содержание SI-EP3/V

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA SI-EP3/V, Техническое руководство

Результаты поиска

Содержание SI-EP3/V

Отзывы:

Бренды по названию

Популярные бренды