YASKAWA SI-EP3/V Скачать руководство пользователя страница 38

Страница: 38 / 53

8 Communication

YASKAWA

SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V Technical Manual

1009

Heatsink Overtemp (oH)

• Check ambient temperature
• Check drive cooling fan

100A

Heatsink Max Temp (oH1)

Check drive cooling fan

100B

Motor Overload (oL1)

• Check the load, accel/decel and cycle times
• Check motor rated current (E2-01)

100C

Inv Overload (oL2)

• Check the load, accel/decel and cycle times
• Check drive rating

100D

Overtorque Det 1 (oL3)

• Check L6-02 and L6-03 settings
• Check system mechanics

100E

Overtorque Det 2 (oL4)

• Check L6-05 and L6-06 settings
• Check system mechanics

100F

DynBrk Transistor (rr)

Cycle drive power and replace drive if fault continues

1010

DynBrk Resistor (rH)

Check load, operating speed and deceleration time

1011

External Fault 3 (EF3)

• Multifunction digital input set to external fault
• Circuit at terminal is closed

1012

External Fault 4 (EF4)

1013

External Fault 5 (EF5)

1014

External Fault 6 (EF6)

1015

External Fault 7 (EF7)

1016

External Fault 8 (EF8)

<2>

1017

Heatsink Fan (FAn)

Check drive cooling fan

1018

Overspeed Det (oS)

• Check reference and reference gain
• Check F1-08 and F1-09 settings

1019

Speed Deviation (dEV)

• Check load, accel/decel times and system mechanics
• Check F1-10 and F1-11 settings

101A

PG Open (PGo)

<2>

Check PG card connections

101B

Input Phase Loss (PF)

Excessive input voltage fluctuation

101C

Output Phase Loss (LF)

• Check for broken wire/loose terminals
• Check motor rating

101D

None

101E

Operator Disconnected (oPr)

Reconnect the digital operator

101F

EEPROM R/W Error (Err)

Cycle drive power and replace drive if fault continues

1020

None

1021

Comm Error (bUS)

• Check network cable connections.
• Check 24 Vdc power supply voltage

1022

Check option installation and connections.

1023

Cycle drive power and replace option or drive if fault continues.

1024

1025

Out of Control (CF)

• Check motor parameters
• Auto-tune

1027

External Fault 0 (EF0)

• Check PLC program
• Check MI switch setting
• Check option LEDs for fault indication

<1> Drive error code is stored in MEMOBUS/Modbus address 0080 hex.

<2> Not available in V1000-series drives.

Drive Alarm

Code

(hex)

<1>

Description

Corrective Action

Содержание SI-EP3/V






















































Результаты поиска

Содержание SI-EP3/V

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA SI-EP3/V, Техническое руководство

Результаты поиска

Содержание SI-EP3/V

Отзывы:

Бренды по названию

Популярные бренды