YASKAWA S-V Seres Скачать руководство пользователя страница 70

Страница: 70 / 88

11 SERVOPACK with Semi-closed Loop Control for Linear Motors

11-2

11.1

Magnetic Pole

For driving linear motors, the magnetic pole should be coordinated. The parameters in the following table are
used for that.



Parameter Setting

Note: In case the hall sensor is not available refer to chapter 11-4.

Parameter

Function

Default Value

When enabled

No.

Dig.

Pn080

Application Function Select Switch 80

Hall Sensor Selection

After restart

Enables hall sensor

Disables hall sensor

Pn081

Application Function Select Switch 81

Hall Sensor Signal Inversion

After restart

Does not inverse the signals (Pos-Logic)

Inverses the signals (Neg-Logic)

Positive logic

Pn080.0 = 0
Pn081.3 = 0

Pn080.0 = 0
Pn081.3 = 1

Pn080.0 = 1
Pn081.3 = 0

Negative logic

Available

Not available

Hall Sensor

Hall Sensor Signal

Parameter Setting

Содержание S-V Seres

























































































Результаты поиска

Содержание S-V Seres

Отзывы:

YASKAWA S-V Seres, Руководство пользователя, Страница: 70 / 88

Результаты поиска

Содержание S-V Seres

Отзывы: