manualshive.com logo in svg

YASKAWA S-V Seres, Руководство пользователя, Страница: 51 / 88

Поделиться
Скачать
YASKAWA S-V Seres Скачать руководство пользователя страница 51

8.2  Setup Procedure

8-7

8

Set-up Procedure for Semi-closed Loop Control

(3) Precautions

If the scale parameters have not been written in the module, A.CA0 (Encoder Parameter Error) will occur 
when the power in turned ON. Monitor the scale data using the monitoring function to see if the scale parame-
ters are saved in the module. If they are not saved, write the scale parameters and then turn the power OFF and 
then ON again to monitor the scale data.

If the proper scale parameters have not been written, the following alarms will occur when the power is turned 
ON:

    A.8A0 (External Encoder Error), A.8A1 (External Encoder Error of Module),
    A.8A2 (External Encoder Error of Sensor), A.8A3 (Extern Encoder Error of Position)

(4) How to Monitor the Scale Data Using the Digital Operator

Note: If a feedback option card is not connected, the following message will appear.

Step

Display Example

Description

1

Press the 

 Key to open the Utility Function Mode 

main menu.

and select Fn01F using 

 or 

 key.

3

Press the 

 key, and the encoder ID will be shown.

Use the 

and 

 Keys to scroll left and right 

through the information.

5

Press the 

 Key.

The display returns to the Utility Functions Mode main menu.

B B             - FUNCTION -
Fn01E:SvMotOp ID
Fn01F:FBOpMot ID
Fn020:S-Orig Set
Fn030:Soft Reset

B B             - FBOpMotID -
Encoder
UTTAH-U11DB
Serial No.
11 bit - INC

Encoder Type/Resolution

Encoder Type

B B             - FUNCTION -
Fn01E:SvMotOp ID
Fn01F:FBOpMot ID
Fn020:S-Orig Set
Fn030:Soft Reset

B B             - FBOpMotID -

  Not available

Содержание S-V Seres

























































































Отзывы:

Нет отзывов