YASKAWA S-V Seres Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 88

YASKAWA S-V Seres Скачать руководство пользователя страница 67

10.3 Pole Detection Functionality

10-5

10

SER

VOP

ACK with Semi-closed Loop Control for Rotary Motors

After the function has been completed the motor power will turn OFF and the Servo Ready signal will turn
ON. Then the function cannot be executed even if the /P-DET signal is turned ON and OFF. Then the control
power is restored, the function must be executed again.



Utility Function: Pole Detection (Fn080)

This utility function is executed using Panel operator, Digital operator and S.

(3) Execution of the Function with MECHATROLINK and Network Option Model



Servo ON Command



Utility Function: Pole Detection (Fn080)

This utility function is executed using Panel operator, Digital operator and S.

(4) Related Parameters

Type

Name

Connector Pin No.

Setting

Description

Input

/S-ON

CN1-40
[Factory setting]

ON

Motor power is ON.
Motor will be ready for operation (/S-RDY signal is
ON).

OFF

Motor power is OFF.

/P-DET

Must be allocated

ON

The function is executed only once then the signal
turns ON for the first time.

OFF

-

Type

Name

Description

Servo ON

Incremental Encoder

The function is executed only once when the command is sent. Then,
motor will be ready for operation.

Absolute Encoder

In the Pn587.0 = 1 setting, the function is executed only once when
the command is sent. Then, motor will be ready for operation.

Servo OFF

Motor power is OFF.

Parameter

Function

Default Value

When enabled

No.

Dig.

Pn481

Polarity Detection Speed Loop Gain [0.1 Hz]

40.0

Immediately

Pn482

Polarity Detection Speed Loop Integral Time [0.01 msec]

30.00

Immediately

Pn486

Polarity Detection Command Accel/Decel Time [msec]

25

Immediately

Pn487

Polarity Detection Constant Speed Time [msec]

0

Immediately

Pn488

Polarity Detection Command Waiting Time [msec]

100

Immediately

Pn490

Polarity Detection Load Level [%]

100

Immediately

Pn493

Polarity Detection Command Speed [min

-1

]

50

Immediately

Pn494

Polarity Detection Range [0.001 rev]

0.250

Immediately

Pn495

Polarity Detection Confirmation Torque Command [%]

100

Immediately

Pn498

Polarity Detection Allowable Error Range [deg.]

10

Immediately

Pn587

Polarity Detection for Absolute Scale Selection

-

-

0

0

Does not detect polarity

0

Immediately

1

Detects polarity

«
...
65
66
67
68
69
...
»

Содержание S-V Seres

























































































Отзывы:

Нет отзывов