YASKAWA S-V Seres Скачать руководство пользователя страница 47

Страница: 47 / 88

8.2 Setup Procedure

8-3

Set-up Procedure for Semi-closed Loop Control

8.2.1

Feedback Option Module Set-up

The scale parameters must be written into the module via the SERVOPACK using the S software
engineering tool.

Note: This feature is available in S Version 5.6.1 and later.

(1) Set-up Procedure

Install a motor, scale and SERVOPACK.

Request the motor parameter file of the installed motor from YASKAWA Europe GmbH.

In S select “Parameters > Parameter edit”.
Set parameter Pn00B.3 = 1.

Start “Setup > Motor parameter scale write” in S.

Write the parameters of the motor parameter file to the scale.

Note: Refer to S Operation Manual for information on how to write parameters using S.

USB cable

Personal Computer

Scale parameter file

Write scale parameters into the feedback
option module via SGDV SERVOPACK

SGDV SERVOPACK

Linear Motor

USB cable

Personal Computer

Scale parameter file

Write scale parameters into the feedback
option module via SGDV SERVOPACK

SGDV SERVOPACK

Motor

Содержание S-V Seres

























































































Результаты поиска

Содержание S-V Seres

Отзывы:

YASKAWA S-V Seres, Руководство пользователя, Страница: 47 / 88

Результаты поиска

Содержание S-V Seres

Отзывы: