YASKAWA FSDrive-MV1000 Series, Инструкция по эксплуатации

Страница: 58 / 260

2.2 Mechanical Installation
58 YASKAWA ELECTRIC TOEP C710687 02B FSDrive-MV1000 Instructions
u
Installing Cooling Exhaust Covers
• Cooling exhaust covers to be fitted at the top of the drive are delivered as accessories.
Install the cooling exhaust covers provided as accessories after installing the drive.
• Bolts for securing the cooling exhaust covers are provisionally set in the drive where the covers are to be installed.
Remove these bolts and install the cooling exhaust covers with them. Take proper precautions to avoid dropping
fasteners into the panel.
• The number of locations where the cooling exhaust covers should be installed differs depending on the model of the
drive.
• When transporting the drive or installing the cooling exhaust covers, be careful not to damage the cooling fans.
u
Installing a Drive on a Floor
Table 2.17 shows the dimensions and the number of mounting holes for each voltage class when installing a drive on a
floor.
Use mounting bolts, nuts, washers, S-washers, and taper washers of M12 diameter to secure the drive.
Secure the drive with bolts in all the designated holes. Secure the drive with bolts in all the designated holes even in
normal installation environments where there is minimal or no vibration. Refer to
Dimensions on page 66 for details on
the mass of the drives.
Table 2.17 Drive Installation and Mounting Hole Dimensions
Voltage
Class
(kV)
Model
CIMR-MV2 †
Bottom
Dimension
Drawing
Installation Dimensions (mm)
Mounting Holes
N -
φ
(mm)
W1 W2 W3 W4 W5 d
2
A † A † 052
<1>
Figure 2.23
720 – – – – 980 6 -
φ
17
A † A † 058
<1>
720 – – – – 980 6 -
φ
17
A
†
A
†
077
<1>
720 – – – – 980 6 -
φ
17
A † A † 093
<1>
720 – – – – 980 6 - φ 17
A † A † 102
<1>
720 – – – – 980 6 -
φ
17
A † A † 115
<1>
720 – – – – 980 6 -
φ
17
A † A † 135
<1>
720 – – – – 980 6 -
φ
17
A † A † 160
<1>
Figure 2.24
730 780 – – – 1230 12 -
φ
17
A † A † 180
<1>
730 780 – – – 1230 12 -
φ
17
A † A † 205
<1>
– – – – – – – –
A † A † 220
<1>
– – – – – – – –
A † A † 280
<1>
– – – – – – – –
A † A † 330
<1>
– – – – – – – –
A
†
A
†
390
<1>
– – – – – – – –
A † A † 440
<1>
– – – – – – – –
A † A † 505
<1>
– – – – – – – –
A † A † 550
<1>
– – – – – – – –
A † A † 600
<1>
– – – – – – – –
3
C † C † 035
Figure 2.25
855 855 – – – 930 6-
φ
17
C † C † 050 855 855 – – – 930 6-
φ
17
C † C † 070 855 855 – – – 930 6-
φ
17
C † C † 100 855 855 – – – 930 6-
φ
17
C † C † 140 855 855 – – – 930 6-
φ
17
C † C † 200
<2>
Figure 2.26 1260 1260 – – – 1030 8-
φ
17
C † C † 260
<2>
Figure 2.27
680 830 – – – 1130 12-
φ
17
C † C † 330
<2>
680 1130 – – – 1530 12-
φ
17
C † C † 400
<2>
680 1130 – – – 1530 12-
φ
17
C
†
C
†
520
<2>
Figure 2.28
490 950 960 – – 1530 18-
φ
17
C † C † 650
<2>
565 950 960 – – 1530 18- φ 17