Yardistry MERIDIAN OCTAGON YM11924, Инструкция по установке и эксплуатации

Страница: 22 / 50

22
support@yardistrystructures.com
D: Place one Rail Assembly between Left Wall Assembly and one Main Wall Assembly. Rail Assembly should sit
tight to top of post inserts. At an angle, attach (1064) Top Rail to posts with two #8 x 2-1/2” Wood Screws. (F7.4,
F7.5 and F7.6)
E: For each (1066) Spindle which is next to a post, at an angle, pre-drill with a 1/8” drill bit then attach (1066)
Spindles to posts, on an angle, with two #8 x 3” Wood Screws per post. (F7.4 and F7.7)
x 3
Step 7: Frame Assembly
Part 2
STEP 9 - Frame Assembly Cont'd
A: Place Beam (1062) in between Left Wall from previous step and 1 Wall Assembly, flush to
each end then attach together using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large
Washer, Lock Nut)
B: Attach Short Gusset Left (1073) and Right (1072) using 5/16” x 2¼” Hex BLT (1/4 LG Washer, 5/16
T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Attach Rail/Post Assembly to the Posts using (2) #8 x 2-1/2” Wood Screws following the pilot
holes
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post. a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
(1066) Spindle
#8 x 3”
Wood
Screw
Hardware
4 x #8 x 2-1/2” Wood Screw
8 x #8 x 3” Wood Screw
Post
STEP 9 - Frame Assembly Cont'd
A: Place Beam (1062) in between Left Wall from previous step and 1 Wall Assembly, flush to
each end then attach together using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large
Washer, Lock Nut)
B: Attach Short Gusset Left (1073) and Right (1072) using 5/16” x 2¼” Hex BLT (1/4 LG Washer, 5/16
T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Attach Rail/Post Assembly to the Posts using (2) #8 x 2-1/2” Wood Screws following the pilot
holes
F7.4
F7.5
F7.6
#8 x 2-1/2”
Wood Screw
Notice screw
attached at an
angle
(1064)
Top Rail
Post
Rail
Assembly
Main Wall
Assembly
Left Wall
Assembly
(1064)
Top Rail
STEP 5 - Wa
ll A
ssembly -(x2)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto one Rail/Post frame from previous
step. ˜ush t o each end then
attach togeth-er using #8 x 3” Wood Screws and 1/4 x
5“ Hex Bolt (1/4” Large Washer, Lock Nut,
135º Bracket)B: Attach Short Gusset Left (1073) and Right (1072) using 5
1/46”
x 2 1/4”
Hex BL
T (1/4 LG
Washer,
5/16 T-Nut, Lock
Washer), then tighten corner using 1/4 x 1-15/16”
Lag Screws (1/4”
Lg
Washers)
C: Repeat steps from above for one more assembly
Tight
Post
F7.7
Pre-drill and
attach screws at
an angle
Post
Insert