background image

 2 

[email protected]

Important Safety Notice!

General Information

Yardistry components are intended for privacy, decorative and ornamental use only.

Product is NOT INTENDED for the following:

  

•  A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.

 

• As load bearing support for a building, structure, heavy objects or swings.

 

•  Used in structures that trap wind, rain or snow that would create extra load on the 

product.

Accumulated snow must be removed from roof.

DO NOT 

climb or walk on roof for any reason.

Permanent structures may require a building permit. 

 As the purchaser and or installer of this 

product you are advised to consult local planning, zoning and building inspection departments for 

guidance on applicable building codes and/or zoning requirements.

Wood is NOT flame retardant and will burn.

  Grills, fire pits and chimineas are a fire hazard if 

placed too close to a Yardistry structure.  Consult user’s manual of the grill, fire pit or chimnea for 

safe distances from combustible materials.

Wear gloves to avoid injury

 from possible sharp edges of individual elements before assembly.

During installation, follow all safety warnings provided with your tools and use OHSA 

approved  safety glasses

.  Some structures may require two or more people to install safely.

Check for underground utilities before digging or driving stakes into the ground!

It is important during assembly to closely follow the instructions

, complete the assembly 

on a solid level surface and that you follow the instruction to square up, level and anchor the 

structure, this will reduce the gap at wood connections during assembly.

General Information:

  Wood components are manufactured with Cedar (C. Lanceolata) 

which is protected with factory applied water-based stain.  Knots, small checks (cracks) and 

weathering are naturally occurring and do not affect the strength of the product.  Annual 

application of a water-based water repellent sealant or stain is important and will help reduce 

weathering and checks.

www.yardistrystructures.com

Questions? 

 Call toll free or write us at:

1 (888) 509-4382

[email protected]

Patents Pending

Содержание MADISON YM11783X















































Отзывы: