Yanmar SK1550 Скачать руководство пользователя страница 79

Страница: 79 / 99

Service - 78

SK1550 Operator’s Manual

Procedures

Filter, Air

Check before startup and every 10 hours. Change when needed.

Check

Check air filter service indicator (1). Change filter

when red band on indicator is visible.

Change

1. Remove cover (5).
2. Remove primary element (4).
3. Wipe inside of housing (2) and cover.
4. Insert secondary element (3) and ensure it is

seated correctly.

5. Insert new primary element.
6. Install cover with dust ejector (6) facing

down.

7. Reset air filter service indicator.

Filter, Fuel

Change filter (shown) every 500 hours. If refueling

from cans, replace filters more often.

NOTICE:

Only open air filter housing when red band on indicator is visible. Change the elements. Do

not attempt to clean them.

• Improperly installed primary element can lead to premature engine failure.
• Compressed air or water can damage filter elements.
• Tapping filter elements to loosen dirt can damage elements.

t53om040w20.eps

t53om041w20.eps

Содержание SK1550




































































































Результаты поиска

Содержание SK1550

Отзывы:

Похожие инструкции для SK1550

Бренды по названию

Популярные бренды

Yanmar SK1550, Руководство оператора

Результаты поиска

Содержание SK1550

Отзывы:

Похожие инструкции для SK1550

Бренды по названию

Популярные бренды