Yamato WG 1000 Скачать руководство пользователя страница 9

Страница: 9 / 56

Before Using this unit

Requirements for Installation

8. Connection of power cord

•

Always ensure that breaker on power unit side is "Off" before connecting power cord. Power

plug of WG250 uses 3-core cord including grounding wire, and the plug is grounded type. If
your plug socket is not compatible (2P), use a ground adapter attached in nonstandard. In
using ground adapter, be sure to ground a grounding lead.

9. Connect the water supply hose securely

•

If not connecting the water supply hose securely, the water supply hose or connection port

may be disconnected, resulting in water leakage such as water bursting forth.

•

Take the connection port body and supply hose out of attachments to the unit. Install the unit

on a horizontal and stable place nearby tap and sink.

10. Connect the tap side

1. Slide the sleeve of socket

③

on connection port side in the arrow direction, then connection

port body and water supply hose can be separated. There separate the two parts.

2. Once loosen the plug

②

from the ring

①

3. Tighten the 4 mounting screws

⑤

uniformly while pressing the ring

①

slightly and uniformly

to make the packing

⑥

in flat contact with water tap. If the tap is a chemical tap, adjust the

position so that the mounting screw is located at the bottom valley of tap nipple as shown.

4. Turn the plug

②

clockwise to tighten securely. This will allow the tap and connection port to

be sealed by packing

⑥

5. Insert the socket

③

securely to the plug

②

with the sleeve slid in the arrow direction. The

sleeve returns to the original position when released, and then connection is completed.

In case that the socket is removed, the valve attached on the connection side of the main unit

stops the flow of water.

WG250

WG1000

Tap

Connection
port body

Socket on
connection
port side

Water supply
hose

Water supply port

Sleeve on water

supply port

Water supply port

Sleeve on water

supply port

Connection Port Body

①

Ring

②

Plug

③

Socket

④

Spacer

⑤

Mounting Screw

⑥

Packing

⑦

Filter

One-touch
Joint

④

⑤

⑥

⑦

①

②

③

Tap

Sleeve

Water supply hose

Содержание WG 1000

























































Результаты поиска

Содержание WG 1000

Отзывы:

Бренды по названию

Популярные бренды

Yamato WG 1000, Инструкция по эксплуатации

Результаты поиска

Содержание WG 1000

Отзывы:

Бренды по названию

Популярные бренды