background image

Yamarin Cross 53 Bow Rider 

30 (40) 

 

 

 

Familiarise yourself with the service procedures shown in the engine manual (see annex).  
Carry out the procedures carefully, or ensure they are performed by an accredited service 
company   
 

6.1

 

   

Washing and waxing the boat 

 
Cleaning fibreglass surfaces 
 

Normally it is sufficient to just wash and wax the deck. Special boat cleaning agents are most 
suitable for the purpose. Do not use strong solvents; they can cause glossy surfaces to fade. 
Mildly abrasive polishes can be used to remove chafes and embedded dirt from the deck. 
The boat's aluminum and fibre glass surfaces can be washed with a pressure washer. Follow  
the chemical manufacturer's instructions when washing and cleaning the deck. 

  

  
 
Useful tip: 

Washing the boat will be easier if it is done immediately after 
getting the boat out of the water. 

 

NOTE!  

Do not spray water with a pressure washer on the caulking seam 
under the rubbing strip. Pressurised water can damage the glued 
seam. 

 
The hatches of the glove compartment and instrument panel are made of plastic and can be 
washed with soap water; never use solvents to clean them. 
 

Cleaning the aluminum hull 
 

The hull should be washed with a special aluminum cleaning agent. 
 Follow the chemical manufacturer's instructions when washing and cleaning the hull. 
Remember to dry the boat. 
 
The waterline and bottom of the boat must be washed in temperatures of at least +10 °C, 
and only after the hull is completely dry.    
          

 

 

Protecting the aluminum hull 
 

When the aluminum hull is completely clean and dry, it can be protected against oxidation. 
Ask recommendations for suitable products from your local dealer. Oxidation is a natural 
reaction of aluminum against corrosion and does not affect the boat's quality. 
 
Useful tip: When the boat has been washed with tap water, a thin chalk-like layer of lime 
and minerals will remain on the boat’s surface after it has dried. The problem can be 
eliminated by adding a few drops of pine oil soap into a bucket of rinsing water, which will 
soften it. 

 

 

Содержание Cross 53 Bow Rider









































Отзывы: