background image

NOTE:

WARNING

CAUTION:

EB001000

NOTICE

This manual was produced by the Yamaha Motor Company, Ltd. primarily for use by Yamaha dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manu-
al, so it is assumed that anyone who uses this book to perform maintenance and repairs on Yamaha
motorcycles has a basic understanding of the mechanical ideas and the procedures of motorcycles
repair.
Repairs attempted by anyone without this knowledge are likely to render the motorcycles unfit for use.

Yamaha Motor Company, Ltd. is continually striving to improve all its models. Modifications and signifi-
cant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers and
will appear in future editions of this manual where applicable.

Designs and specifications are subject to change without notice.

IMPORTANT INFORMATION

Particularly important information is distinguished in this manual by the following.

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to
the motorcycle operator, a bystander or a person inspecting or repairing the
motorcycle.

A CAUTION indicates special precautions that must be taken to avoid damage
to the motorcycle.

NOTE:

A NOTE provides key information to make procedures easier or clearer.

Содержание YZF-R6 2000

































Отзывы: