Yamaha YFM350RB Скачать руководство пользователя

Страница: 97 / 140

8-17

6. Wash the sponge material gently but thor-

oughly in solvent. WARNING! Always use
parts cleaning solvent to clean the sponge
material. Never use low-flash-point sol-
vents or gasoline to clean the sponge ma-
terial because the engine could catch fire
or explode.

[EWB01941]

7. Squeeze the excess solvent out of the sponge

material and let it dry. NOTICE: Do not twist
the sponge material when squeezing it.

[ECB00441]

8. Check the sponge material and replace it if

damaged.

9. Apply Yamaha foam air filter oil or other qual-

ity foam air filter oil to the sponge material.

TIP
The sponge material should be wet but not drip-
ping.

10. Pull the sponge material over the air filter ele-

ment frame.

11. Apply all-purpose grease to the air filter ele-

ment seat.

12. Insert the air filter element into the air filter

case, and then install the air filter case cover
by hooking the holders onto the air filter case.

1. Air filter element retaining plate
2. Air filter element frame

3. Sponge material

4. Air filter element seat

U1BS62E0.book Page 17 Monday, April 18, 2011 6:43 PM

Содержание YFM350RB













































































































































Результаты поиска

Содержание YFM350RB

Отзывы:

Похожие инструкции для YFM350RB

Бренды по названию

Популярные бренды

Yamaha YFM350RB, Руководство пользователя

Результаты поиска

Содержание YFM350RB

Отзывы:

Похожие инструкции для YFM350RB

Бренды по названию

Популярные бренды