manualshive.com logo in svg

Yamaha YFM350RB, Руководство пользователя

Поделиться
Скачать
Yamaha YFM350RB Скачать руководство пользователя страница 106

8-26

8

The top of the brake pedal should be positioned
50.2 mm (1.98 in) above the top of the frame as
shown. If the brake pedal is not positioned as spec-
ified, have a Yamaha dealer adjust it.

EBU24713

Adjusting the parking brake free play 

The parking brake free play must be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
Cable length “A” should measure 64–68 mm
(2.52–2.68 in). Adjust the parking brake free play
as follows.

1. Release the parking brake by moving the

parking brake lever to the right.

2. Fully loosen the locknut and the adjusting bolt

at the rear brake caliper.

3. Slide the rubber cover back at the brake ca-

ble.

4. Loosen the locknut.
5. Turn the adjusting nut on the brake cable in di-

rection (a) to increase the cable length, and in
direction (b) to decrease it.

1. Brake pedal height

1. Locknut
2. Adjusting bolt

3. Cable length “A”

U1BS62E0.book  Page 26  Monday, April 18, 2011  6:43 PM

Содержание YFM350RB













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды