Yamaha YFM350RB Скачать руководство пользователя

Страница: 109 / 140

8-29

TIP
If the specified clutch lever free play could be ob-
tained as described above, skip steps 4–8.

4. Fully turn the adjusting bolt at the clutch lever

in direction (a) to loosen the clutch cable.

5. Slide the rubber cover back at the crankcase.
6. Loosen the locknut.
7. To increase the clutch lever free play, turn the

adjusting nut at the crankcase in direction (a),
and to decrease it, turn the nut in direction (b).

8. Tighten the locknut at the crankcase, and then

slide the rubber cover to its original position.

9. Tighten the locknut at the clutch lever, and

then slide the rubber cover to its original posi-
tion.

TIP
If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate cor-
rectly, have a Yamaha dealer check the internal
clutch mechanism.

EBU24845

Drive chain slack

The drive chain slack should be checked before
each ride and adjusted if necessary.

To check the drive chain slack

1. Place the ATV on a level surface.

TIP
When checking and adjusting the drive chain
slack, there should be no weight on the ATV and
all tires must be touching the ground.

2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

1. Locknut

2. Clutch lever free play adjusting nut (crankcase)

3. Rubber cover

(a)

(b)

U1BS62E0.book Page 29 Monday, April 18, 2011 6:43 PM

Содержание YFM350RB













































































































































Результаты поиска

Содержание YFM350RB

Отзывы:

Похожие инструкции для YFM350RB

Бренды по названию

Популярные бренды

Yamaha YFM350RB, Руководство пользователя

Результаты поиска

Содержание YFM350RB

Отзывы:

Похожие инструкции для YFM350RB

Бренды по названию

Популярные бренды