manualshive.com logo in svg

Yamaha YFM350RB, Руководство пользователя

Поделиться
Скачать
Yamaha YFM350RB Скачать руководство пользователя страница 49

6-2

6

Position (3):
Cold engine start with ambient temperature
above 25 °C (80 °F).

Ambient temp./starter (choke) position

6. Completely close the throttle lever and start

the engine by pushing the start switch.

TIP
If the engine fails to start, release the start switch,
then push it again. Pause a few seconds before
the next attempt. Each cranking should be as short

as possible to preserve battery energy. Do not
crank the engine more than 10 seconds on each
attempt.

7. If the engine is started with the starter (choke)

in position (1), the starter (choke) should be
returned to position (2) to warm up the engine.
If the engine is started with the starter (choke)
in position (2), keep the starter (choke) in this
position to warm up the engine.

8. Continue warming up the engine until it idles

smoothly, then return the starter (choke) to
position (3) before riding.

TIP
The engine is warm when it responds quickly to the
throttle with the starter (choke) turned off.

NOTICE

ECB00163

For maximum engine life, never accelerate
hard when the engine is cold!

1. Fully open

2. Half open

3. Closed
4. Starter (choke)

U1BS62E0.book  Page 2  Monday, April 18, 2011  6:43 PM

Содержание YFM350RB













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды