Yamaha YFM350RB страница 101 Скачать руководство пользователя | Manualshive

Страница: 101 / 140

background image

8-21

8

TIP
The engine is warm when it quickly responds to the
throttle.

2. Attach the tachometer to the spark plug lead.
3. Check the engine idling speed and, if neces-

sary, adjust it to specification by turning the
throttle stop screw at the carburetor. To in-
crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).

TIP
If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24047

Adjusting the throttle lever free play

The throttle lever free play should be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
The throttle lever free play should measure 2.0–
4.0 mm (0.08–0.16 in) as shown. Periodically
check the throttle lever free play and, if necessary,
adjust it as follows.

TIP
The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle le-
ver free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle lever free play, turn

the throttle lever free play adjusting bolt in di-
rection (a). To decrease the throttle lever free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U1BS62E0.book Page 21 Monday, April 18, 2011 6:43 PM

«
...
99
100
101
102
103
...
»

Содержание YFM350RB













































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM350RB

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды