manualshive.com logo in svg

Yamaha TW200Z, Руководство пользователя

Поделиться
Скачать
Yamaha TW200Z Скачать руководство пользователя страница 84

 

10-1

 

1

2

3

4

5

6

7

8

9

10

 

CONSUMER INFORMATION

 

EAU26352

 

Identification numbers 

 

Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi-
cle is stolen.
KEY IDENTIFICATION NUMBER:

VEHICLE IDENTIFICATION 
NUMBER:

MODEL LABEL INFORMATION:

 

EAU26390

 

Key identification number 

 

The key identification number is
stamped into the key. Record this num-
ber in the space provided and use it for
reference when ordering a new key.

 

EAU26400

 

Vehicle identification number 

 

The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.

TIP

 

The vehicle identification number is
used to identify your motorcycle and
may be used to register your motorcy-
cle with the licensing authority in your

 

area.

 

1. Key identification number

1

 

1. Vehicle identification number

1

Содержание TW200Z



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды