manualshive.com logo in svg

Yamaha TW200Z, Руководство пользователя

Поделиться
Скачать
Yamaha TW200Z Скачать руководство пользователя страница 67

 

PERIODIC MAINTENANCE AND ADJUSTMENT

 

7-31

 

2

3

4

5

6

7

8

9

of contact, administer the fol-
lowing FIRST AID.

 

●

 

EXTERNAL: Flush with plenty
of water.

 

●

 

INTERNAL: Drink large quan-
tities of water or milk and im-
mediately call a physician.

 

●

 

EYES: Flush with water for 15
minutes and seek prompt
medical attention.

 

●

 

Batteries produce explosive hy-
drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.

 

●

 

KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF

 

CHILDREN.

 

7. Place the battery in the battery

compartment, and then hook the
battery band onto the holder.

8. Connect the breather hose to the

battery and make sure that it is
properly routed.

9. Connect and tighten the positive

battery lead to the battery’s posi-
tive (+) terminal.

10. Connect and tighten the negative

battery lead to the battery’s nega-

tive (-) terminal.

11. Install the seat.

 

To store the battery

 

1. If the vehicle will not be used for

more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.

 

NOTICE:

 

 When removing the

battery, be sure the key is
turned to “OFF”, then discon-
nect the negative lead before
disconnecting the positive
lead.

 

[ECA16302]

 

 

2. If the battery will be stored for more

than two months, check the specif-
ic gravity of the electrolyte at least
once a month and fully charge the
battery whenever necessary.

3. Fully charge the battery before in-

stallation.

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals and
that the breather hose is properly
routed, in good condition, and not
obstructed. 

 

NOTICE:

 

 If the

breather hose is positioned in

 

1. Battery breather hose

1. Battery

2. Battery breather hose

1

1

2

Содержание TW200Z



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды