manualshive.com logo in svg

Yamaha TW200Z, Руководство пользователя

Поделиться
Скачать
Yamaha TW200Z Скачать руководство пользователя страница 44

 

PERIODIC MAINTENANCE AND ADJUSTMENT

 

7-8

 

1

2

3

4

5

6

7

8

9

 

EAU18722

 

Removing and installing the 
cowling and panels 

 

The cowling and panels shown need to
be removed to perform some of the
maintenance jobs described in this
chapter. Refer to this section each time
the cowling or a panel needs to be re-
moved and installed.

 

EAU18810

 

Cowling A

 

To remove the cowling
Remove the screw, and then pull the
cowling off as shown.

To install the cowling
Place the cowling in the original posi-
tion, and then install the screw.

 

EAU32451

 

Panel A

 

To remove the panel
Remove the screws, and then pull the
panel out at the area shown.

To install the panel
Place the panel in the original position,
and then install the screws.

 

1. Cowling A

2. Panel A

1

2

 

1. Panel B

1. Screw

1

1

 

1. Panel A

2. Screw

2

1

Содержание TW200Z



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды