Yamaha TW200Z Скачать руководство пользователя страница 64

Страница: 64 / 98

PERIODIC MAINTENANCE AND ADJUSTMENT

7-28

EAU23250

Lubricating the rear
suspension

The pivoting points of the rear suspen-
sion must be lubricated at the intervals
specified in the periodic maintenance
and lubrication chart.

EAU23272

Checking the front fork

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

WARNING! To avoid injury,

securely support the vehicle so
there is no danger of it falling
over.

[EWA10751]

2. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

NOTICE

ECA10590

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-

pair it.

1. Grease nipple

Recommended lubricant:

Lithium-soap-based grease

Содержание TW200Z



































































































Результаты поиска

Содержание TW200Z

Отзывы:

Бренды по названию

Популярные бренды

Yamaha TW200Z, Руководство пользователя

Результаты поиска

Содержание TW200Z

Отзывы:

Бренды по названию

Популярные бренды