Yamaha TW200Z Скачать руководство пользователя страница 73

Страница: 73 / 98

PERIODIC MAINTENANCE AND ADJUSTMENT

7-37

6. Connect the speedometer cable.

EAU25080

Rear wheel

EAU25421

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it

falling over.

1. Loosen the axle nut.
2. Remove the brake pedal free play

adjusting nut, and then disconnect
the brake rod from the brake cam-
shaft lever.

3. Turn the drive chain adjusting

plate on each side of the swingarm
fully in direction (a).

4. Lift the rear wheel off the ground

according to the procedure on
page 7-35.

5. Remove the axle nut, and then pull

the wheel axle out.

6. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

TIP

The drive chain does not need to be
disassembled in order to remove and

install the wheel.

1. Axle nut

2. Brake pedal free play adjusting nut

3. Brake rod

4. Brake camshaft lever

5. Drive chain slack adjusting plate

(a)

Содержание TW200Z



































































































Результаты поиска

Содержание TW200Z

Отзывы:

Бренды по названию

Популярные бренды

Yamaha TW200Z, Руководство пользователя

Результаты поиска

Содержание TW200Z

Отзывы:

Бренды по названию

Популярные бренды