Yamaha Star XV19CTSZ 2009 страница 75 Скачать руководство пользователя

Страница: 75 / 104

PERIODIC MAINTENANCE AND ADJUSTMENT

7-27

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

WARNING! Do not

use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.

[EWA15131]

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAU39124

Replacing a headlight bulb

This model features a headlight
equipped with two quartz bulbs. If the
high beam or the low beam bulb burns
out, replace it as follows.

NOTICE

ECA10650

Take care not to damage the follow-
ing parts:

●

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-

1. Fuse box
2. Auxiliary DC connector fuse

3. Signaling system fuse

4. Ignition fuse
5. Backup fuse (for clock)

6. ECU fuse

7. Headlight fuse
8. Taillight fuse

9. Spare fuse

Specified fuses:

Main fuse:

50.0 A

Headlight fuse:

20.0 A

Signaling system fuse:

10.0 A

Ignition fuse:

25.0 A

Fuel injection system fuse:

15.0 A

ECU fuse:

10.0 A

Auxiliary DC connector fuse:

3.0 A

Taillight fuse:

10.0 A

Backup fuse:

10.0 A

1. Low beam headlight bulb

2. High beam headlight bulb

U2C514E0.book Page 27 Tuesday, September 8, 2009 10:12 AM

Содержание Star XV19CTSZ 2009









































































































Результаты поиска

Содержание Star XV19CTSZ 2009

Отзывы:

Похожие инструкции для Star XV19CTSZ 2009

Бренды по названию

Популярные бренды

Yamaha Star XV19CTSZ 2009, Руководство пользователя

Результаты поиска

Содержание Star XV19CTSZ 2009

Отзывы:

Похожие инструкции для Star XV19CTSZ 2009

Бренды по названию

Популярные бренды