Yamaha Star XV19CTSZ 2009 страница 77 Скачать руководство пользователя

Страница: 77 / 104

PERIODIC MAINTENANCE AND ADJUSTMENT

7-29

2. Disconnect the headlight coupler,

and then unhook the headlight
bulb holder.

3. Remove the burnt-out bulb.

4. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

5. Connect the coupler, and then in-

stall the headlight bulb holder cov-
er by turning it clockwise.

To replace the low beam headlight bulb

1. Disconnect the headlight coupler,

and then remove the burnt-out
bulb by turning it counterclock-
wise.

2. Install a new bulb by turning it

clockwise.

3. Connect the headlight coupler.

Installing the headlight unit

1. Install the headlight unit by install-

ing the screws.

2. Connect the coupler to the head-

light body cover.

3. Install the headlight body cover by

installing the bolts.

4. Install the windshield.
5. Have a Yamaha dealer adjust the

headlight beam if necessary.

1. Headlight bulb holder cover

1. Headlight coupler

2. Headlight bulb holder

1. Headlight coupler
2. Headlight bulb

U2C514E0.book Page 29 Tuesday, September 8, 2009 10:12 AM

Содержание Star XV19CTSZ 2009









































































































Результаты поиска

Содержание Star XV19CTSZ 2009

Отзывы:

Похожие инструкции для Star XV19CTSZ 2009

Бренды по названию

Популярные бренды

Yamaha Star XV19CTSZ 2009, Руководство пользователя

Результаты поиска

Содержание Star XV19CTSZ 2009

Отзывы:

Похожие инструкции для Star XV19CTSZ 2009

Бренды по названию

Популярные бренды