Yamaha Star XV19CTSZ 2009 страница 41 Скачать руководство пользователя

Страница: 41 / 104

INSTRUMENT AND CONTROL FUNCTIONS

4-25

EAU38353

Auxiliary DC connector

NOTICE

ECA15311

The accessory connected to the
auxiliary DC connector should not
be used with the engine turned off,
and the load must never exceed 36
W (3 A), otherwise the fuse may blow
or the battery may discharge.

WARNING

EWA12531

To prevent electrical shock or short-
circuiting, make sure that the cap is
installed when the auxiliary DC con-
nector is not being used.

A 12-V accessory connected to the
auxiliary DC connector under the rider
seat can be used when the key is in the
“ON” position.

1. Auxiliary DC connector
2. Auxiliary DC connector cap

U2C514E0.book Page 25 Tuesday, September 8, 2009 10:12 AM

Содержание Star XV19CTSZ 2009









































































































Результаты поиска

Содержание Star XV19CTSZ 2009

Отзывы:

Похожие инструкции для Star XV19CTSZ 2009

Бренды по названию

Популярные бренды

Yamaha Star XV19CTSZ 2009, Руководство пользователя

Результаты поиска

Содержание Star XV19CTSZ 2009

Отзывы:

Похожие инструкции для Star XV19CTSZ 2009

Бренды по названию

Популярные бренды