Yamaha PC412-D страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 101

background image

4.7. Switching the power between standby/on

To prevent loud noise from being emitted from the speaker when the power is turned on, power-on each unit in
the order of audio sources, mixer, and finally the amp. When turning the power off, reverse this order.

■

Standby

→

power on

1. Hold down the power switch for two seconds or longer.

The power turns on, and the button changes from blinking to lit (green). After a time, the HOME screen
(VOLUME) appears.

■

Power on

→

standby

1. Press the power switch.

The display shows a confirmation message.

2. Turn the main knob to select "YES," and then press the main knob to confirm; the power switches to

standby mode.

NOTE

• The settings at the time the power was turned off (the state when disconnected from the AC outlet)

are saved. The next time the power is turned on, the unit starts up with those settings.

NOTICE

* When this product is connected to an AC outlet, it is in standby mode, and a small amount of current is
flowing. If you will not be using this product for an extended period of time, be sure to disconnect the power
supply plug from the AC outlet.

4. Connections

18

| PC412-D PC412-DI PC406-D PC406-DI Owner’s Manual

«
...
19
20
21
22
23
...
»

Содержание PC412-D






































































































Отзывы:

Нет отзывов

Похожие инструкции для PC412-D

Бренд: dB Technologies Страницы: 133

Crush PiX 50BXT

Бренд: ORANGE Страницы: 15

Бренд: Soldano Страницы: 8

Бренд: Preamble Instruments Страницы: 22

Бренд: T+A Страницы: 40

Бренд: Polk Audio Страницы: 13

Бренд: Sansui Страницы: 14

Бренд: Cloud Страницы: 7

Бренд: Marshall Electronics Страницы: 1

Sonic Frontiers SFS-40

Бренд: Sonic Frontiers Страницы: 6

Бренд: Sams Страницы: 18

Бренд: Redback Страницы: 2

Бренд: Radial Engineering Страницы: 8

Бренд: AR Страницы: 58

Бренд: SpeakerCraft Страницы: 7

Бренд: Tavish Design Страницы: 34

Бренд: NAIM Страницы: 160

Бренд: LOOPTROTTER Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды