Yamaha PC412-D страница 10 Скачать руководство пользователя | Manualshive

Страница: 10 / 101

background image

removing the power cord, pull the latch toward yourself, turn the connector counterclockwise, and remove it.

WARNING

You must use the included power cord. Do not use the included power cord with any other product.
Doing so may cause malfunction, overheating, and fire.

NOTICE

• When this product is connected to an AC outlet, it is in standby mode, and a small amount of current

is flowing. If you will not be using this product for an extended period of time, be sure to disconnect
the power supply plug from the AC outlet.

• Position the power cord so that the rear exhaust does not contact it directly. The temperature of the

rear exhaust might cause the power cord to deform.

⑩

Exhaust vent

This is an exhaust vent for the cooling fan. Because warm air is expelled through this vent, take care that it is not
blocked by an obstruction.

⑪

[SPEAKERS] A/B/C/D connectors

These are the output connectors to the speakers. There are the following two types of connector.

WARNING

Do not touch the pins of unused channels, or allow them to short.
High voltage is present even at unused pins.

●

PC-D series

Four Speakon output jacks (NL4) are used to connect speakers.
The outputs of this product can be bridged in pairs of two channels.

There are no dedicated outputs for use in bridge mode. For the pin assignments, refer to "

Speaker connections

●

PC-DI series

This product uses Euroblock connectors (7.6 mm 8-pin) for speaker connections.
The outputs of this product can be bridged in pairs of two channels.

There are no dedicated outputs for use in bridge mode. For the pin assignments, refer to "

Speaker connections

⑫

Dante [PRIMARY]/[SECONDARY] ports

This is an etherCON (RJ-45) port for connection to a CL-series unit or other Dante device via an Ethernet cable
(CAT5e or better is recommended). For the PC-D series, use RJ-45 connectors that comply with Neutrik
Corporation’s etherCON CAT5. For the PC-DI series, use RJ-45 connectors.

NOTE

• To prevent electromagnetic interference, use STP (Shielded Twisted Pair) cables. For STP cables,

use conductive tape to securely connect the metal portion of the connector to the shielded portion
of the cable.

2. Panel descriptions

PC412-D PC412-DI PC406-D PC406-DI Owner’s Manual |

7

«
...
8
9
10
11
12
...
»

Содержание PC412-D






































































































Отзывы:

Нет отзывов

Похожие инструкции для PC412-D

Бренд: NAD Страницы: 2

Бренд: E&I Страницы: 13

Sound Wave 115S

Бренд: Ibanez Страницы: 2

Бренд: Harman Kardon Страницы: 11

Бренд: R.V.R. Electronica Страницы: 36

Бренд: Sure Electronics Страницы: 16

Бренд: NAD Страницы: 37

Бренд: Rockford Fosgate Страницы: 12

Бренд: B&K Страницы: 16

FIVE OR SEVEN CHANNEL 125.5 S2

Бренд: B&K Страницы: 12

Бренд: Luxman Страницы: 18

Бренд: Kingsman Страницы: 4

PowerTech PT 2.1

Бренд: Crown Страницы: 1

Бренд: Nakamichi Страницы: 15

Бренд: VAC Страницы: 19

Бренд: VUE Audiotechnik Страницы: 10

Бренд: ARC Audio Страницы: 10

GM 7200M - Amplifier - 500 Watts x 1

Бренд: Pioneer Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды